Jump to content
Moto Apps That Are Da $#@!??? Read more... ×

How to Replace the Clutch Basket in your Dirt Bike


Rob@ProX

Is your clutch having problems engaging and disengaging? Do you feel inconsistency through the clutch lever when operating the clutch? A worn clutch basket could be the cause. In this article, we’ll look at diagnosing a worn clutch basket, review replacement options, and step through the process of replacing the clutch basket so that the next time you need to tackle the job, you’re well prepared.

314793783_Photo1.jpg.093607f0dad69ede4e72c8a37868df84.jpg

Time to replace your clutch basket? Read on for a step-by-step on getting your clutch working smoothly again!

Diagnosing the Issue

Any clutch issues that a machine may have are typically very apparent to the rider because there is a complementary feeling of loss of control of the machine. The machine won’t become outright unrideable; however, subtleties that quickly become annoying will arise when utilizing the clutch. Most notably, modulation of the clutch may become more difficult, and the clutch feel will be inconsistent.

Before taking the machine apart, verifying possible simple issues such as clutch cable adjustment and that the engine or gearbox oil has been maintained regularly should be confirmed. To inspect and disassemble the clutch, the procedures outlined in the machine’s factory service manual should be followed. Once the clutch has been removed from the engine, inspecting its condition is straightforward.

827189984_Photo2.jpg.b5becc79898ce7391e99bf5029f71208.jpg

Double check that any issues you may be experiencing are in fact caused by a worn basket and not from a different culprit, like a clutch cable.

Click here for tips on replacing a clutch cable.

The basket consists of a series of “fingers,” or “tangs” which mate with the friction discs. The basket fingers drive the friction discs. The friction discs slide out when the clutch is engaged and back in when the clutch is disengaged. Due to this interaction, notching can occur on the edges of the basket fingers. Any notching that can be felt with a pick or a fingernail can be potentially problematic. In terms of clutch basket wear, the main grounds for replacement of the basket are worn and grooved basket fingers.

1450139492_Photo3.png.0e283f2151c874d0a3408442ee19a40d.png

Notching on basket tangs is typically part of normal wear and is the main reason to warrant basket replacement.

Replacement Options

The clutch basket is a great component to upgrade since it has surfaces such as the basket fingers that are inherently wear surfaces. Selecting a ProX basket, which is significantly stronger and more wear resistant than OE baskets, has a high return on investment in terms of reduced maintenance and improved performance. ProX clutch baskets are precision machined from forged 7075-T6 aluminum, which is one of the strongest alloys on the market. Wear resistance is ensured by utilizing a sophisticated hard anodizing process. A final layer of performance is added in the form of a Teflon coating which seals the basket surfaces and allows the friction discs to slide effortlessly over the clutch basket fingers while in operation.

243015103_Photo4.png.42ca795cee5db13bb31f861ed585daae.png

ProX clutch baskets are forged from aluminum, precision machined, and hard anodized and Teflon coated for smooth clutch actuation. The tensile strength of the material combined with the coatings make notching the basket tangs almost impossible.

Find ProX clutch components for your bike or ATV here!

Tools Required

The clutch basket is an assembly of parts including the basket, starter gear, clutch driven gear, dampers, and backing plate. The starter gear is pressed into the clutch basket, and the driven gear, dampers, and backing plate are riveted or screwed in place. When it comes to tools, you’ll need the following, outside of your standard tools used to remove the clutch from the machine:

  •  Hydraulic press or vice - capable of exerting up to 8 tons of force.
  •  Center punch, drill and drill bits, or grinder, or mill - for removing the rivets
  •  Punch and hammer - for driving the rivets out of the assembly
  •  Torque wrench and Loctite - for securing the screws in the new basket
  •  Fixturing - for adequately supporting the basket while removing and installing the starter gear. The fixturing doesn’t have to be anything fancy, and examples are provided later in this article.

1417644902_Photo5.jpg.424f759d3dda826f7fe8b2b169b4d007.jpg 1410338955_Photo6.jpg.1dcc25fa0d42deb2d0239d9e8a487593.jpg

There a number of tools required to do the job correctly. For example, having the ability to properly press the starter gear out and in is key to retaining proper function.

The Process

We’re going to jump into the process post clutch removal and focus on servicing the basket. ProX clutch baskets include new dampers and screws along with instructions for your specific application. The following instructions should be considered supplementary.

  1. Mark the backing plate and gear - Use a marker to mark the outside surfaces of the backing plate and gear. Doing so will ensure that these parts are installed in the correct direction when reassembled.

    328650575_Photo7.jpg.aa2e51f86f2304f4d83fedd88d480100.jpg
     
  2. Removing the rivets - It is preferable to drill the rivet heads off, however, grinding and milling the heads off are also acceptable options. When drilling, it is best to start by using a center punch to indent the center of the rivet so that the drill bit will not walk. Once center punched, start with a small drill bit and work up to a bit that is slightly smaller in diameter than the rivet itself. Only drill down far enough to remove the head from the rivet. Typically, a depth of 0.040 - 0.080” (1-2mm) below the surface is all that is required to drill out the rivet head. After the rivet head has been drilled out, use a punch and hammer to drive the rivet out of the assembly. 

    328113981_Photo8.JPEG.07230bbd292b37d32f226c9d47eb3f8e.JPEG 245022848_Photo9.jpg.46d4d00107fce41c825e2296ec8cfecb.jpg
    The most recommended method to remove the rivets is to drill the heads off then use a punch to remove the rest of the rivet completely.
     
  3. Remove the driven gear - Pull the backplate off before removing the driven gear. Note the orientation of the dampers. Take the driven gear off, then remove the dampers.

    168944907_Photo10.jpg.74d69ccd3f5bfaac38faa976c529829a.jpg 1860591355_Photo11.jpg.20b2f94abe78111238a323822c12d84a.jpg
    Make sure you note the orientation of the dampers before removing them all after removing the driven gear.
     
  4. Remove the starter gear - The starter gear utilizes an interference fit with the clutch basket, so it will have to be pressed out. The exact geometry of the starter gear will be model specific. Some starter gears will feature teeth that bite into the clutch basket. Depending on the starter gear geometry and geometry of the clutch basket, it is possible the clutch basket will be destroyed during the removal process. 

    44465114_Photo12.jpg.9b7cbc33f2977b2c8f729058a4d53877.jpg 1643955091_Photo13.jpg.5dd2b6beec250bf5fd0ed9e55809297e.jpg
    Starter gears will differ depending on the model. Make sure it's adequately supported to press out without damaging the gear.

    Adequately support the clutch basket around its base so that loads applied will transfer through the center of the basket. Standoffs may need to be utilized to support the basket properly. Select an appropriately sized spacer to place between the starter gear and press. Appropriately sized sockets can serve as suitable spacers. Carefully press the gear out of the hub.

    986942762_Photo14.jpg.4835fecd5c2e2c13ce2b6e337481dfb4.jpg 943090083_Photo15.jpg.a8c305fc8cef01ec3b4633154640ee9e.jpg
    There's a good chance the old basket may break when pressing the starter gear out. This is fine, the focus is on not damaging the gear itself.
     
  5. Clean the parts - Remove any clinging material from the starter gear, clean the driven gear and backplate.
     
  6. Install the starter gear - Apply engine oil to the outside of the starter gear. Carefully position it in the center of the new clutch basket. Before pressing it in, be sure to confirm any specific press-in depth requirements outlined in the instructions. Ensure the clutch basket is adequately supported before pressing the gear in place. The press force required to install the gear will be model specific and highlighted in the installation instructions.

    2003662124_Photo16.jpg.8eeff4f727af64fb3d9144bbfb0b3cfe.jpg
    Be sure to oil the starter gear and note any depth and force specifications for your specific application.

    On some models, a simple shrink fit is utilized to install the starter gear. When this process is specified, follow the heating instructions for the clutch basket. Once up to temperature, carefully drop in the starter gear.
     
  7. Install the driven gear and dampers - Place the driven gear on the clutch basket noting any orientation requirements previously identified. Install the new dampers in the correct orientation.

    783506137_Photo17.jpg.27ee93d3129773618b36d649506190b2.jpg
    Install your new dampers in the correct orientation and reinstall the primary gear.
     
  8. Install the backplate - Double check the orientation of the dampers and driven gear. Install the backplate onto the clutch basket, noting any orientation requirements. 
     
  9. Torque the backplate screws - Consult the installation instructions for the proper torque specs, apply Loctite if the screws are not pre-Loctite, then tighten in a cross-pattern.

    1881156895_Photo18.jpg.5a7f4dd33f04f673f011d77e230f54cb.jpg
    Reinstall your back plate with new screws and thread locking compound and torque them to spec.

At this point, the clutch basket is ready for service and can be reinstalled on the engine. Refer to your service manual for assembly instructions and specifications to reinstall your clutch and button up the engine.

The process of replacing a clutch basket is straightforward and can be executed by anyone so long as the necessary steps are followed and tools are available. We hope this write-up simplifies the job and helps our fellow riders and racers get back out there performing better than before!

1951705182_Photo19.jpg.8282ba581c8578eee60e1a588efd9882.jpg

  • Helpful 2


User Feedback

Recommended Comments

There are no comments to display.



Create an account or sign in to comment

You need to be a member in order to leave a comment

Reply with:


  • Similar Content

    • By Dylan Swicegood
      Recently got this bike and it was pretty neglected by previous owners. I decided to do some maintenance due to the fact that I broke my wrist.
       I noticed trying to replace the fork seals and bushings that the left side damper compresses and stays compressed fully while the right side pushes in and back out. Any reason as to why?  
      Also the bushings on the dampers are different on both sides. Is that normal? 





    • By Ian Oakes
      Hi,
      Earlier this year I put a Lifan 125 with an automatic clutch into an XR70 for my 9 year old son. Now he's learnt to ride the automatic clutch had become a problem as he's unable to pop the clutch to do wheelies and donuts etc (although he taught himself to slightly depress the gear lever slightly to disengage the clutch and pop the front wheel). I know I can swap the motor out for about $280 AUD off ebay, but I was wondering if it was possible to do a conversion. I've found the following parts on ebay
      Clutch case
      Manual Clutch
      I know I'll also need a lever and cable, but what other parts do you think I'll require?
      I've also seen a conversion kit for $165 USD, but it's for 88 to 108cc engines and once I convert it to local currency and pay for postage I might as well buy another engine, which won't go down well with the wife.
      Any ideas would be greatly appreciated.
    • By Gatorade88
      I have never paid for a brand new dirt bike but might consider it sometime in the future. What's your guys' opinion on maintenance on a newer bike. Is it hard or easy? I have no problem working on dirt bikes at all but have never worked on things like fuel injection, air forks, etc.
    • By BlackEagle077
      I found an old ASV clutch lever in my dad's old motocross gear. I assume it is for a 05-10 KX250F. It was still in the box and looked brand new. I have a 15 YZ250FX and was wondering if the lever could fit on my bike. The ASV clutch lever has a hot start lever on it, my bike does not. If I can't fit the lever on my bike it will give it to one of my friends. One has an 07 YZ250f and the other has a 12 KX250f. If I can fit the lever on my bike could i do anything with the hot start lever or will it just have to hang there?

    • By Jp-2405
      Hi I have a 2017 ktm 85sx 17/14. I was wondering is there anyway to adjust my clutch because when I first start to ride it seems to be dragging a little bit like when I’m in first going down a hill it will engine break a little(not enough to hurt it but I still blip the throttle to be safe)Is there any way to adjust it like a cable. I read the factory manual and all it says is to adjust the lever but I don’t know if that would help but I will try. Any suggestions?
×