Jump to content
Sign in to follow this  

The 6 Steps in Winterizing your Ride


Eddie Sisneros

The best and most successful method to winterize your dirt bike is to not stop riding during the winter months. Unfortunately, many enthusiasts live in areas of the country where they really have no other choice but to store their bike for the winter. How you choose to store your machine will make your springtime start up a happy day or an expletive filled adventure. So, what steps should you take to winterize your ride? Click to page two where we'll cover step 1 of The 6 Steps in Winterizing your Ride.


ccs-3-0-71493500-1475251150.jpg







Exterior Preparation
Clean the entire bike with a mild detergent and water. Avoid directly spraying bearings and seals as to not force water into them. If you use a pressure wash, be VERY careful of this. If possible, start and ride the bike to evaporate any water trapped in the motor and drag your brakes to dry them as much as possible. Clean your chain with a bristled brush and mild degreaser, such as most household dish soaps. Liberally spray your clean chain with WD-40 (Water Displacement 40th Attempt) and wipe off the excess with a shop rag. Finish the process with your favorite spray chain lube. If you have an o-ring chain, make sure to use o-ring safe lube. While you’re still in lube mode, take your WD-40 and spray down the foot peg pivots, kick start pivot, folding shifter pivot and lever pivots. When doing this, it’s a good time to inspect brake pads, suspension linkage, chain and sprockets and such for wear. If your motorcycle is equipped with grease zerk fittings, go ahead and give them a few squirts of quality grease. Lastly, air up the tires to spec.


ccs-3-0-52943900-1443779851.jpg




Next: Fuel System



Fuel System
There are different methods of winterizing fuel systems, but these are the methods I prefer, having had good luck with them throughout my lifetime. If your bike has a steel fuel tank, it’s very important to fill it to the brim with fuel. Filling the tank completely will stop it from rusting, which is a major issue in some areas. Plastic fuel tanks are more forgiving, but keeping it full will minimize the formation of condensation. Fuel stability is another concern, as most fuels begin to breakdown after about 60 days. I prefer to fill the tank with race fuel. In contrast to pump fuels, race fuels can be left for longer periods of time and will not turn to varnish. The alternative is a product called Sta-Bil. Many people use this product with good results and it is a safe bet when race fuel isn’t available. Once the fuel has been stabilized, start the motorcycle and let the fuel circulate throughout the entire system.




ccs-3-0-78457500-1443780444.jpg




Next: Electrical System



Electrical System
Not all dirt bikes have a battery, but if you’re lucky enough to own a bike with a magic button, this area concerns you. I prefer to use a product called Battery Tender. It keeps the battery fully charged by using a float charge that keeps the battery peaked. Battery life has lot to do with the climate it’s stored in. If your bike is stored in an unheated area, remove the battery from the bike and store it in a heated a space. Basements, storeroom or a even a closet will work. Keeping the battery from freezing along with a Battery Tender or like product will keep the battery at its best.




ccs-3-0-81792700-1443780684.jpg




Next: Engine & Cooling System



Engine & Cooling System
A fresh oil change should be done before you store your bike. Dirty engine oil contains corrosive contaminates that you don’t want to leave in the engine over the winter. I also prefer to install a fresh spark plug at the same time. If you’re in a coastal region, a fogging oil should be applied through the spark plug hole also. The fogging oil will be available at some auto parts stores and definitely at boat/marine shops. With the spark plug out, shoot a few sprays down the spark hole and turn the motor over a few times. Once the fogging oil has been applied, install the fresh spark plug. The cooling system should also be prepared. You need to make sure that the coolant is up to spec. Fresh coolant is a good idea, but you can check the condition with a hydrometer that should be available at any auto parts store. With any motorcycle fluid, when in doubt change it. Besides engine fluids, the brake and clutch fluid (KTM or Magura Juice Clutch) should be topped off and replaced if there is any doubt. Brake fluid naturally draws moisture over time, so changing it before you store you bike each year is a good idea.




ccs-3-0-75238000-1443781134.png




Next: Storage Location



Storage Location
Now that your motorcycle has been prepared for storage, it’s time to choose a location. If you have the luxury of heated storage, all the better. The less you expose the motorcycle to extreme temperature fluctuations the better. Once the location has been chosen, I recommend putting the motorcycle up on a stand. Using a stand keeps the weight off the tires, eliminating the possibility of creating flat spots. This also allows the suspension to relax from the weight of the bike. If a stand is not option, using a piece of plywood to park the motorcycle on will keep the tires from dry rotting, sitting on a cold concrete floor. Once the motorcycle is situated, throw an old blanket or tarp over it. This will keep the dust to a minimum. If you are in a coastal region, skip on the cover. This may trap moisture under the cover, contributing to corrosion. In fact, coastal riders should also not be afraid to liberally apply WD-40 to the exterior of their motorcycle.


ccs-3-0-43204900-1443782044.jpg




Next: Spring Prep



Next Spring
When the wonderful sights and smells of spring arrive, it’s time to ride! Since you did all the work when you stored your bike for the winter, spring start up will be a breeze. Install the battery if so equipped. Drain the carb float bowl to allow fresh gas from the tank in. Even though the fuel was stabilized, the small volume that is contained in the float bowl will deteriorate much quicker than the much larger volume in the tank. Double check all fluids and you may even consider changing the oil again if it was stored for an inordinate amount of time. Check the air pressure in the tires and your ready to fire it up. If you did your job correctly, the motorcycle should spring to life. Take a extra few minutes at warm to check for any fluid leaks or strange noises. If all is good, you’re ready to tear it up!

Next: Year Around Riding Option




If you just gotta ride year around, consider a snowbike conversion kit such as this kit from the folks at MotoTrax:


ccs-3-0-16639400-1475682110.jpg




 


We want to hear from you!
We recognize that like most things, there are a number of different ways to accomplish the same task. We'd love to hear what's been successful in how you winterize your stuff, so don't be shy! Help us expand this topic by posting to the comments section below. :thumbsup:

Sign in to follow this  


User Feedback

Recommended Comments

There are no comments to display.



Create an account or sign in to comment

You need to be a member in order to leave a comment

Reply with:


  • Similar Content

    • By Serg Orlovskiy
      hey so i encountered a problem so i drained all the coolant, and checked the valves on the bike and it was all in clearance, put it all together filled up the coolant, fired up, let it sit in the garage for a bit noticed coolant leaked out the over flow
      and i went ahead and topped it off and let it sit for a while
      and i just looked at it there was what looked like probably most of the coolant that was in the bike on the floor 
      anyone have any idea what i should do next? the store is closed so i can't buy anymore coolant atm i use engine ice.
    • By Paranoia
      Hello. My CRF450R 2011 have leaking (oil with coolant) from water pump drainage hole:

      I install new mechanical seal (7), oil seal (16) and new bearing (15):

      Filled new coolant and run my bike, all was fine, but after 15 minutes I got heavy coolant leaking:

      Disassembled again and noticed that "head" of mechanical seal is disconnected:

      What's can be wrong? Looks like problem with slight tightening (torque) (12 N/m) of impeller (part #6)?
      Sorry for my bad English.
    • By t__bird
      First-time poster here.
      I have a 99 YZ125 that's been causing me a whole lot of headache trying to dial in the jetting. I've given up and since ordered a Lectron Carburetor (waiting for it in the mail). After last weekend's ride I was doing some research into why my bike smokes a lot even with how much I've leaned it out (per JD jetting recommendations and then some). I learned that sometimes a faulty clutch-side crankcase seal can leak transmission oil into the crankcase and cause excessive smoking. This would make sense as last time I changed my oil a very small amount came out from the transmission.  I've ordered a seals kit.
      With that knowledge, I decided to tear down the bike and inspect the top-end. Here's what I found. What is this milky, white substance? Coolant leaking? I've also ordered a water pump rebuild kit.
      ALSO, I discovered that the cylinder bolt next to the power valve linkage was completely off the dowel and wedged behind the power valve linkage. I torqued this bolt to spec using the Motion Pro torque wrench adapter. Do these need to be Loctited? Could this loose bolt be causing coolant to leak into the cylinder??
      Other info:
      – Always clean air filter
      – Low (20ish) hours on the piston, rings, and gaskets
      – FMF pipe and silencer (packing looked good when I removed last night, will replace)
      – I did give the bike a good pressure wash (with muffler plug and airbox cover), so maybe it's water?
      – 91 pump gas with Maxima Castor oil
      – 10w-30 oil

    • By Edward Fuller
      Hello everyone,
      This is my first post here so I apologize if I'm posting in the wrong thread or something like that. Anyways, a few days ago(Friday the 13th) I decided to take my 2001 Drz400E out for a spin in the woods outside my neighborhood. Long story short, I drowned the thing. Three hours and a lot of cussing later and I got the thing out of the mud and back home. Moral of the story? Stick to the trails.
      When I got the thing back home I discovered two problems:
      1.) The bike was leaking coolant, No clue where from.
      2.) The bike wouldn't rev over 4.5k rpm. If I give it more gas, it stalls.
      I did some research on the rev thing and apparently cleaning the carb/jet fixes this(If anyone can confirm this it'd be helpful). I removed the carb, cleaned it, and everything looks fine. I haven't tested it, however, because of the coolant leak. I figured running the bike with next to no coolant probably isn't a good idea. I also don't feel like putting everything back on the bike just to end up tearing it apart to fix the other stuff. I heard from a friend that water could have caused a gasket to leak, but I'm not exactly eager to tear apart my engine to find out.
      If you guys could give me any advice, it'd be a big help(Especially since I've got a road trip planned for memorial day).
       
    • By ReeveC
      https://www.walmart.com/ip/Prestone-Extended-Life-Prediluted-Antifreeze-Coolant/16879961?wmlspartner=wlpa&adid=22222222227017563295&wl0=&wl1=g&wl2=c&wl3=40840067792&wl4=aud-273067695102:pla-78653338832&wl5=9007323&wl6=&wl7=&wl8=&wl9=pla&wl10=8175035&wl11=online&wl12=16879961&wl13=&veh=sem
       
      is this coolant good to use in a drz400?
×