Jump to content
Antigravity Batteries Product Giveaways - ENTER NOW! Read more... ×

2002 Honda XR250R seat and gas tank compatability

Recommended Posts

Hi,

I have a 2002 Honda XR250R and I love the bike but the gas tank but, let's be honest, it is quite bland. The seat also dips quite low in comparison to the top of the gas tanks so cornering is more difficult compared to other bikes. I was wondering if there is any street bikes (such as the newer xr250 or the cr230) who's gas tank and seat is interchangeable with my older XR. I have looked at aloop kits and such but they are just too expensive. Not the older XR has a single beam to the handle bars while the newer Hondas have a "double wishbown" frame style. 

Thanks so much

Edited by Destructokhan

Share this post


Link to post
Share on other sites

I have heard that the A Loop kit uses a modded 1998 CR250 tank and seat.  I may be wrong, but it may be worth a look if you can find one.

Share this post


Link to post
Share on other sites
5 hours ago, Firestone said:

This question has been asked a thousand times. I have not seen anyone answer yet with a good option.

I bought a used- half priced Aloop kit to get the cost down.

Used A Loop kit?  Those are less common than unicorns.

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Reply with:


  • Similar Content

    • By Ktm520sxrider
      Ready to seal back up





    • By hondahondo
      A few picks of my winter project.













    • By Big64N
      Good condition with a long list of high end upgrade parts.
      Rekluse EXP 3.0 with cover and slave
      EVO- Ellensburg suspension tuning for 6' 200# expert rider
      Fork bleeders
      Trail-tech map switch
      Moose 1-1/8 flex bar
      CYCRA probend bar guards
      SXS skid plate with linkage plate
      Clutch and water pump guards
      Frame guards
      Fastway Evolution III pegs
      SRT Pro Armor radiator and rear rotor guards
      Acerbic Front rotor guard
      TM designs chain guides
      DID race chain
      Renthal sprockets
      Gripper seat
      FMF F-bomb header
      Dirt Tricks timing chain tensioner
      Pro Wheel, wheels
      Tubliss front and rear
      New top end and valve adjustment 60 hours old
      Many more aftermarket parts as well as spare parts and service manuals included in the sale.  Willing to include 4 sets of tires with 80% tread left for full price.
      Great bike with plenty of life left and set up for anything from single track woods to wide open dessert.
      Can hang with any of the 450's but is much easier to handle in the tight woods.
      Priced to sell at $6000.00 
      Willing to consider reasonable offers but no trades or carry.
    • By riverside21
      Has anybody purchased/used one of these Arrowhead IHA6017 cdi boxes??  I tried 2 different ones of these on a 1987 and 1994 XR200R, and the bikes won't even start.  Bikes just pop and backfire, had to put the old cdi's back on.  I noticed when I ordered the boxes they stated "advance ignition curves" in the specs.  The box is also much bigger than the stocker and won't fit in the rubber mount.  I didn't mess with moving around the timing to try and get these to work....I just sent them back.  
    • By riverside21
      Recently picked up a 1987 xr200r in pretty good condition, all stock.  The carb was all gummed up and running real rich, and the previous owner removed the baffle and end cap from the exhaust, but left the air box top chute in place.  I cleaned up the carb and verified all stock jetting, needle position, air screw, etc.  Where we live the quieter the better for off-roading so I ordered a new baffle and end cap, but did ride the bike for a week before the parts arrived.  With the muffler parts out I had a brown plug and plenty of power throughout the entire throttle range.  Got the muffler parts, installed them and now the bike falls flat while climbing hills and gradually rolling on the throttle, I get a burble at low speed sometimes and I have a black sooty plug.  I'm kind of at a loss on this one.  I realize that the parts restricted the exhaust....but it's basically back to stock and I've had these bikes stock before and they ran fine.  Seeing as I have all stock jets and am getting a sooty plug, I'm wondering if electrics are weak?  I also tried adjusting the air screw in/out and moving the needle clip to position 2, either of the two made my problem worse.
      Any ideas?
×