Which of these bikes is your primary ride?   3,808 members have voted

  1. 1. Which of these bikes is your primary ride?

    • XR650R
      958
    • XR650L
      1632
    • XR600R
      812
    • XL600
      188
    • Other XL/XR
      164

Please sign in or register to vote in this poll.

4,414 posts in this topic

took it to a local upholstery shop. Had them trim the edges to get some of the 'square' out of it, and then re-covered it with a "leather-like" vinyl material. Looks MUCH better IMO. BTW, I have a winter seat too with more grip on the wet/damp days.

Share this post


Link to post
Share on other sites
Where did you find that Woody tank decal?????? I was trying to find one for my Acerbis tnak, but ended up with a FE one

It's a tank cover that I got from e bay USA.

Took 7 wks to arrive in England

But should be a lot quicker to you!

The companys called Boliviasport I think and it was 30 bucks. :ride:

Share this post


Link to post
Share on other sites

This was last month before my first rally, The Guajira 800

IMG_9269.jpg

And then this is fron the rally, the second one is not from my pig (I broke the gear box).

IMG_0324.jpg

HPIM16031.jpg

Nice place !!!!

Share this post


Link to post
Share on other sites

here's one of my favorite pics our xrs. Several other guys vacation with us every October in Utah (Poison Springs,Factory Butte/Swingarm/Caineville, Henry Mountains, ect..)

Tennessee Pigs @ the Dirty Devil in Poison Springs

3904364889_839bdab19b.jpg

left to right- xr250r(piglett),xr600,xr400,xr650r,xr650r,xr650r

1 person likes this

Share this post


Link to post
Share on other sites
lil air from Centralia revisited tour

miscshit2049.jpg

WOW! i think i saw that bike at tower city a few years ago.

Share this post


Link to post
Share on other sites
How do you get out to take the pictures without getting the tires dirty???

Hello??.....is somebody there??....is dry i guess :busted:

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Reply with:


  • Similar Content

    • By _RaStA_RoCkEt_
      Hey there, TT. What's good... you been partying? Hope so.
       
      ANYHOW;
      Ripping my new (to me) 00' XR-R on some fire roads last night up in the Lost Coast and WHAM! There went the chain! It took the OEM case saver and 1/2-3/4 of each mounting bolt with it... which was concerning, but not as concerning as if I had seen the oil draining from a nice new 'modded' hole in the case cover. Yay! (to cheaper repair) No! (to repairs at all) 
      Few concerns I have about going through the repair process which seems fairly well documented:
      1) Since I nearly sheared the bolts on the sides of the case, I presume that my bike will need the XR's Only case saver. Fortunately, it uses the rear engine mounting bolt to hold on, but still uses the two OEM mounts as well. The top OEM hole seems deep enough to drill easily... but:
      How far can I drill the LOWER one to re-thread w/out punching my feared 'hole in the case'? 
      2) I removed my countershaft sprocket as I sat there waiting for a my AAA flatbed, and noticed that about 1/2 of the countershaft sprocket splines were gone! Further, the retaining ring (w/ the two 10mm head bolts) was worn significantly as well, allowing the countershaft sprocket to do some proper movement...
      Any suggestions on how to fix THAT? 
      (I had this problem (#2) on an XR-L, and replaced with a PBI XR-R sprocket to limit wear, since the splines were longer... this seems a bit worse. I ordered, along with the chain, a Ironman front 15T sprocket to replace my worn PBI... but I dk about 'restoration' of the splines on the countershaft itself.)
       
      Any ideas? / Pictures for the interested... as soon as I find a website that isn't Photobucket! 
    • By Jonathan Wall
      Hi everyone I just purchased a 1986 XL600r that was running ok when I bought it two days ago, but would bog down around 1/4 throttle. I drove it around some yesterday staying off the throttle, and she did fine , but not running quite right.  At one point after shutting her down in town, had a real hard time (10 minutes) trying to restart her. I finally got her started and got her home. I tried to fire her up the next day in order to try and tune the carb for the altitude Im at. 
      Long story short, she just wouldnt start (wheras before it was very easy to start) - almost like she wasnt getting spark. Well I pulled the plug wire boot and the wire was completely disconnected from the coil! I figured this wire having been super loose while riding was likely the poor throttle issue I was having. Well reconnected to the plug wire to what I think was the coil, then pulled the plug to check that it was super black and sooty. I replaced with a new plug and.... still nothing. Not even close to turning over.
      Whats going on here? My next step is replacing the ignition coil and wire with a new one, but anything else I'm missing here? Thanks.
      edit: this bike had a new stator installed last summer.
    • By TheLastByte
      How the hell are you supposed to get that thing out? I bought that overpriced motion pro tool, tried heating it and soaking it, and it still will not move a millimeter. Do I have to use an impact driver, or do I have to drill the peening out? Can I reuse the retainer once it is out? Can I just loctite it back in later, or should I re-peen it?
    • By MurrietaRob
      This bike has only 249 original miles - is OEM including 1994 red, white, and blue color scheme, bike was garaged and covered and only ridden a few miles a year as it was NOOP registered for past 18 years - bike is street registered now, transferred from family, clean title. Only updates are new D606 tires, battery, and all fluids, etc changed.  Bike is in excellent condition and runs even better; includes original tool kit too!
    • By akitsen
      I'm looking to convert my xr650r to full DC power and was wondering if anyone here was using a terminal bus bar ? something like this one : https://www.amazon.com/DSC-TB01-Terminal-Block-Splits-Input/dp/B005K49NMW/ref=sr_1_2?ie=UTF8&qid=1510464051&sr=8-2&keywords=bus+bar&dpID=310kVzto9uL&preST=_QL70_&dpSrc=srch
      I'm looking to make the wiring a bit more simplified if possible, and have a single organized place like this that everything can connect to and run to battery would be incredibly useful.
      Thoughts ? Suggestions ?