3x3 and jetting

I have an 05 DRZ SM...got the dynojet sm specific kit and I'm jetting it as burnd said to the specs for stage two.....it never says anything about the pilot jet...am I missing something or do I need to change it?

The FMF/DJ kit stage 2 instructions assume a standard pilot jet is used, so no need to change the PJ. It makes the mixture adjustment with the 3.5 turns on the fuel screw.

However, id you fit a bigger PJ, you can get away with less turns out on the fuel screw and so less chance of it shaking loose or dropping out.

alright thanks!!

Hey guys! I did the Jet Kit mod way back in the day when Dyno Jet kit was for the S specific model. I am still under the idea i should be using a larger MJ than my 142.5 with a 3x3 hole and full yoshi system. Should i go up to a 147 - 150 MJ ?? It feels just a little light on top? :thumbsup:

Thanks a lot


I've got a 155 main in my SM but I'm pretty sure that the SM kit needle is tapered way different from the S jet kit needle. I think you need both the needle and the bigger jet so it runs right through all the RPM's...not just the bottom or top.

you need both the needle and the bigger jet

Right. I believe the bigger jet takes advantage of the different needle taper. It's a waste to step up to one without the other.

Man, reading this, I think I'll go try some fuel screw tweakage....

So i guess i should swap out the old jet kit for the new or can I just buy the Needle and MJ? I have the 25PJ already installed. Is the SM kit better than the S? More power? :thumbsup: Thanks


you canuse the same needle.just bump the main jet up to a 150.

I was in the same boat as ucantstunt. I had the S jetkit in mine because thats all they had. I sold it to buy the sm jetkit and left the 25 pilot in and it runs a little better. Its just peace of mind.

burned~ U mean the Same needle i have now or use the same needle off of the SM specific kit and bump my jet to 150?


I bought both kits. Bought the s kit first not knowing about the sm kit. The 'sm' needle is on the left and 's' needle is on the right:


Notice the SM is fatter at the end, shorter, and the actual clip notches are lower. I found a marked improvement in the SM needle.


burned~ U mean the Same needle i have now or use the same needle off of the SM specific kit and bump my jet to 150?


you can use the S needle.do use the bigger main jet.

the SM needle is different for sure,but the S needle works ok.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Similar Content

    • By BikeChimp
      I'd like to turn my UK 2004 DRZ400S back to stock airbox (snorkel) and jets, needle shim position etc
      When I bought it the PO had fitted a Sigma6 kit and done the 3x3 mod but is doesn't have a tapered needle like the JD and other kits. Took me ages to get it running right, however it still runs rich and I'm fed up of arsing around with it. 
      So I've bought a standard airbox without 3x3 hole, stock exhaust.
      Q1 The Suzuki manual says this Mukuni BSR36 (29FA) carb should have a 142.5 Main Jet but the Clymer manual say its a 135.  In UK everything's from sea level to 1000m. I'm in Sheffield so nothing gets above 500m even in the Peaks (Hills). Any UK owners or anyone else know what the correct jet should be?
      Q2 Says the original needle is a '5DH36-2nd'. The needle has 5 notches on it. Currently set at 2 clip from bottom. The Suzuki reference says needle is 5DH36-2nd, Does the 2nd bit mean 2nd from top or bottom?
      Q3 - Does anyone have a detailed photo of the shim order just in case it was assembled wrong. (mine is attached)
      I know most people on here are going to be horrified I'm taking back to stock but any help on above would be really appreciated.

    • By Bgringo
      I've read a lot of threads about this but still haven't found exactly what I'm looking for.  I'm pulling my 2004 DRZ400S out of storage sometime this week and getting it ready for the season.  I live at 9,000 ft, but my first ride of the year is probably going to be at around 5,000 ft.  I was going to pull the 145 main jet I'm running and put in the 150 adjusting the needle from the 2 clip to the 3rd, then re-jet once I got home.  I already have the extended fuel mixture screw in place so I started thinking that I should just run the 150 jet set up and adjust the fuel screw to compensate for the higher elevation where I'll be doing most of my riding.  I will be going down in elevation for rides until late May or June depending on snowfall, but riding on the street when I'm able.  Are there any disadvantages with this?
      I'm new to posting on this forum, so please forgive me if I didn't get the right search words in and there is already a post about this.
    • By Markl5557
      I am currently running 10w 40 Belray non synthetic and I want to switch to full synthetic amsoil .... is it ok to switch from regular to synthetic? I have read it’s not safe to go from synthetic to regular can someone explain if it’s safe to go from regular to synthetic!? Thanks !
    • By RockyMtnMark
      Good Morning,
        Last night I measured my valve clearances for the very first time (I know...) on my DRZ400S.  It's a 2002 and I've owned is since 2011.  I bought it with t's got about 15,000 miles on it and most of it's miles these days are on dirt.
      Intake specs are 0.10-0.20 mm.  Exhaust specs are 0.20-0.30
      My intake valve clearances are in spec, forgot to write them down.  My exhaust valve clearances are between 0.1778 and 0.2032 which is slightly out of spec.  They are no more than 25 microns out of spec.  My question is, do I really need to shim these?  Will this kind of out-of-spec cause performance, mechanical, or other losses?  As far as I can tell, I'd have to buy a whole shim kit which is like $80.  Thanks!
    • By Zach440
      Selling my 2009 Drz400sm. Been a great bike but it’s time to let go . Not looking for any trades - spring is just around the corner ! Located in northern Virginia . Cash only $4200- willing to negotiate I have some wolfman luggage options available as well. Love to make a package deal for someone 

      -11640 miles . Mild off-road never wrecked.
      -Oil / filter changed every 1500 miles
      -New did chain , brake pads , front sprocket at 10400 miles .
      - valves checked and within spec at 10,000
      - jetted with JD kit and 3x3 mod
      -doubletake mirrors
      -waterproof usb wired and located next to Speedo
      - drc large foot pegs , barkbusters with integrated turn signals . 12oclocklabs tall delete with upgraded circuit board
      -thumpertalk case savers
      -sergeant seat (amazing) and Clarke 3.9 tank (190mile range )
      - fog lights wired in so they shut off with high beams
      -Shorai lithium battery
      -led headlight

      - stock gas tank and seat will be included

      The bike is dirty in photos and I apologize my water is currently disabled outside due to freezing temps . Radiator guards and skid plate NOT included but can be for some extra $$. Rear tire could be replaced but front is fine .