Jump to content
Sign in to follow this  

OEM 03 XR250 suspension settings (baseline) ??

Recommended Posts

I don't have an owners manual and was just curious as to what the factory settings are on the front and rear susp.. ie.. how many clicks from full stiff out on compression and rebound etc.

Share this post


Link to post
Share on other sites

Here is what my manual says:

Always start from the full hard position which is all the way clockwise.

Front:

Compression -There should be at least 19 clicks total adjustment range.

Standard setting is 7 clicks counterclockwise from full hard.

There are no rebound adjustments on the 250. The screws at the top of the forks are bleeders.

Rear:

Compression - Should have at least 20 clicks total adjustment range. Standard setting is turn adjuster counterclockwise 9-12 clicks until the punch mark on the adjuster lines up with the reference mark. In case you don't know which is which compression adj. is the high one just above the nitrogen bottle

Rebound - Should have at least 20 clicks total adjustment range.

Standard setting is turn adjuster 7-10 clicks counterclockwise until punch mark on adjuster lines up with reference mark. Rebound adjuster is the lower one just below the spring.

The reference marks aren't that easy to see (at least on my '03) but it looks to me like both marks are at the 12 o'clock position.

Sag or preload - Measure the spring length with the rear wheel off the ground.

Standard setting is 7.15 inches or 181.5 mm

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Reply with:

Sign in to follow this  

  • Similar Content

    • By 661Bran28den661
      What’s up guys. Totally new here picked up an XR400R I live in the desert so I’m riding often and enjoy it. But I am having some issues with my  01 XR400R. I brought it out this morning for a putt and it seems to be choking up in the top of second. Like a bog an go bog an go. First seemed fine and third I didn’t make it high enough into the rpms to see. Before I brought it back to the garage. Yesterday I also changed the air filter back to an uni. I had seen the other one had a hole in it and the box was dirty gunned up and oily. I removed the airbox gave it a good clean out wiped everything down very well put a piece of screen over the snorkel Or where it used to be I should say. “Lightly oiled the filter.Also the spark arrester an tip for the bike it did not come with I ended up making one with a piece of flat steel and drilling holes. Whilst doing this. I found also a crack in the pipe. It almost sounds as like there’s a vacuuming or whistle? When revving.The first one I had made worked fine I had no issues. This one I am wondering maybe if it’s a cause of a little too much back pressure.So I’m assuming it’s either a Carb or exhaust problem. Or something that could totally be minuscule. Or major issue. Would definitely like some second opinions and any advice would be greatly appreciated. Thanks guys! 
      TWISTIN THROTTLES & CRACKN BOTTLES


    • By ddickinson
      My lanky 14 year old boy started showing an interest in riding MX/Off-Road so I sourced the best beginner friendly, yet dirt worthy, bike I could find: an Ol' Honda XR250R (2004). So far I've replaced a few clutch levers and perches with stock parts. That's gotten old and I'm looking to upgrade to an ASV or Torc1 type fold-able clutch/perch brake combo. Went to purchase online today and to my surprise there were no such parts listed for the XRs. I saw plenty of CRF/CRF-X choices and they seem to differ depending on generation. Obviously I can use nearly any perch/clutch combo as long as the two match; but I was wondering if anyone knew which of these levers was closest to stock? Also, will the first gen CRF250X brake lever work on the XR? These may be stupid questions to some; but I'd rather ask a dumb question than drop money on an ASV brake lever I can't use. Thanks for any help.
      #xr250r#hondaxr  
       
       

    • By TheLastByte
      Im currently in the market for an xr400r, and considering buying one that's had some heavy engine work done. The current owner claims to have bought it from a friend who's an XR enthusiast. The PO installed a big bore kit and high comp piston, as well as a xrs only pumper carb, rsw triple clamp, aftermarket clutch, street lights, and a whole bunch of bling.
       
      My main concern is the effect the upgrades will have on the engine's longevity. How much quicker will I be going through top ends with the setup on this bike as opposed to a stock setup, and should I be worrying at all about bottom end longevity as well? I wouldn't mind having to eventually redo the top end, but I don't want to deal with a race bike type top end rebuild schedule on an XR. 
      Is there anyone here who's running a bike similar to this one who can give some advice? 
    • By Ralph303
      I have a 2001 Honda XR400R. It has a whirring/grinding sound in the lower end and a vibration in the top end. I pulled the valve cover and everything looks good. Decompression lever looks to be in order. Anyone know where I should start looking or just rebuild the whole engine. Ballin on a budget, but really love this bike. It looks like it’s new otherwise. Oil was jet black and thin. Thanks in advance! 
    • By junglePIG
      Hi, I have an Xr250r with a buckled/ wobbling front wheel, after trying to true the rim i have broken a spoke.
      I am wondering if it is possible to lace any 36 hole aftermarket rim to the oem hub, also will i need to buy an xr250r specific spoke set. also could i take a 36 hole rim from another front wheel and lace that up???? thanks
×