Bike Picture

I couldn't figure out how to post my pic.........but my web page has a picture of my bike with the new black Cycra plastic. Just go to the photo page.


[ December 28, 2001: Message edited by: RiDe101 ]

Nice photos on there!!

[ December 28, 2001: Message edited by: dendrz ]

I still can't get it to work. It only works if I have my web page and thumpertalk open at the same time??????? There is a lot more on my web page anyways. Check it out!


[ December 28, 2001: Message edited by: RiDe101 ]



[ December 29, 2001: Message edited by: SANDRZ ]

Why does black and Yellow look so darn good!!!


Ride101, where did you get the black vinyl that is on your sidepanels? I like the black airbox look. I really like the RM front fender.

I just bought some black backgrounds and cut them to fit. Just follow the lines on the side panel. I plan on kind of customizing some graphics next month along with some handguards. This month is handlebars and grips. Gotta budget the ole' money supply.

Originally posted by RiDe101:

I just bought some black backgrounds and cut them to fit. Just follow the lines on the side panel. I plan on kind of customizing some graphics next month along with some handguards. This month is handlebars and grips. Gotta budget the ole' money supply.

I've thought about making my own. Did you cut the vinyl on or off the bike?

I took off the side panels and just stuck a section of black background on there. Work it from the front of the panel to the back of the panel. The key is make sure that the plastic is super clean and most important, TAKE YOUR TIME. Also, use a hair dryer, it helps cut back on the air bubbles. I used a small razer blade knife to trim it up nice.

Good Luck :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Similar Content

    • By Markl5557
      So I am going to put in an in-line fuel filter just for added protection from stuff in my gas .... and I have always used bronze element cone ones you no what I’m talking about the ones everyone seems to use but upon reading online supposedly that bronze element breaks down and doesn’t catch everything .... I have came across a moose fuel filter that has a fine nylon mesh just like what’s on the petcock filter ... any opinions on which is better ? Bronze element or mesh ?
    • By BikeChimp
      I'd like to turn my UK 2004 DRZ400S back to stock airbox (snorkel) and jets, needle shim position etc
      When I bought it the PO had fitted a Sigma6 kit and done the 3x3 mod but is doesn't have a tapered needle like the JD and other kits. Took me ages to get it running right, however it still runs rich and I'm fed up of arsing around with it. 
      So I've bought a standard airbox without 3x3 hole, stock exhaust.
      Q1 The Suzuki manual says this Mukuni BSR36 (29FA) carb should have a 142.5 Main Jet but the Clymer manual say its a 135.  In UK everything's from sea level to 1000m. I'm in Sheffield so nothing gets above 500m even in the Peaks (Hills). Any UK owners or anyone else know what the correct jet should be?
      Q2 Says the original needle is a '5DH36-2nd'. The needle has 5 notches on it. Currently set at 2 clip from bottom. The Suzuki reference says needle is 5DH36-2nd, Does the 2nd bit mean 2nd from top or bottom?
      Q3 - Does anyone have a detailed photo of the shim order just in case it was assembled wrong. (mine is attached)
      I know most people on here are going to be horrified I'm taking back to stock but any help on above would be really appreciated.

    • By Bgringo
      I've read a lot of threads about this but still haven't found exactly what I'm looking for.  I'm pulling my 2004 DRZ400S out of storage sometime this week and getting it ready for the season.  I live at 9,000 ft, but my first ride of the year is probably going to be at around 5,000 ft.  I was going to pull the 145 main jet I'm running and put in the 150 adjusting the needle from the 2 clip to the 3rd, then re-jet once I got home.  I already have the extended fuel mixture screw in place so I started thinking that I should just run the 150 jet set up and adjust the fuel screw to compensate for the higher elevation where I'll be doing most of my riding.  I will be going down in elevation for rides until late May or June depending on snowfall, but riding on the street when I'm able.  Are there any disadvantages with this?
      I'm new to posting on this forum, so please forgive me if I didn't get the right search words in and there is already a post about this.
    • By Markl5557
      I am currently running 10w 40 Belray non synthetic and I want to switch to full synthetic amsoil .... is it ok to switch from regular to synthetic? I have read it’s not safe to go from synthetic to regular can someone explain if it’s safe to go from regular to synthetic!? Thanks !
    • By RockyMtnMark
      Good Morning,
        Last night I measured my valve clearances for the very first time (I know...) on my DRZ400S.  It's a 2002 and I've owned is since 2011.  I bought it with t's got about 15,000 miles on it and most of it's miles these days are on dirt.
      Intake specs are 0.10-0.20 mm.  Exhaust specs are 0.20-0.30
      My intake valve clearances are in spec, forgot to write them down.  My exhaust valve clearances are between 0.1778 and 0.2032 which is slightly out of spec.  They are no more than 25 microns out of spec.  My question is, do I really need to shim these?  Will this kind of out-of-spec cause performance, mechanical, or other losses?  As far as I can tell, I'd have to buy a whole shim kit which is like $80.  Thanks!