Notoil is it good or not

Hi ! I would like to know if some of you use notoil system for their air filter. Do you like it does it work like they said ( easy cleaning) do you feel your engine is well proteck with this oil , is it very tacky. Please give me your input if you use that.


I like it and have been using it for a few years now. Clean up is easy too. Just don't over oil it or it will be dripping for days. Also, wear gloves.

No Toil = Very Good

I've been using it since '01. I've had 4 bikes since then. Use it as described by the maker; clean your filter as described by the maker and you'll never go back to petroliem based oils. It has saved my marriage because now the house isn't all stunk up with gasoline vapors like it used to be! :thumbsup:

Do a search on it to get mucho info here on TT.

It is the second best product behind the Rekluse z-start automatic clutch you can use on your bike IMHO.

tank,s for your answer , i will go with it.


I love it :thumbsup:

Any of you guys have a problem with the grease that comes with the kit? My buddies have had the grease eat the filter base I seen it twice they change there filter every ride so I don't know what to think about the grease but the oil and cleaner seem to work really well and its easy.

I dunno know about no-toil but I use the uni cleaner and filter foam in the spray cans. Super easy!! just spray the filter with the cleaner rinse let dry then spray it with the foam and install! your done! and the no-toil factory is litterally right behind my house! you would figure I would have tried there product by now.........maybe I just like uni....I dunno. No-toil just seems like a lot of work to me.

Hi ! I would like to know if some of you use notoil system for their air filter. Do you like it does it work like they said ( easy cleaning) do you feel your engine is well proteck with this oil , is it very tacky. Please give me your input if you use that.

NoToil Fast 3 Filters :thumbsup:

Been using them for a year now and love em...

I'm down with No-Toil....

(I like it)

I use a Twin-Air filter and frame with a Napalm filter screw (they work for me.) Use the Notoil oil and cleaner and love it. Some have advised wearing gloves and not over oiling...FOLLOW THAT ADVICE. I also recommend getting a 98-cent spray bottle for the oil. Trying to poor the oil on the filter evenly is a pain. I've found the spray bottle works perfect for applying it and not spilling any. If the openning of spray bottle gets clogged, just run a little hot water over the tip of the bottle and wipe with paper towel. Hope it works out for you!

I'll be odd man out. I used No-Toil for a year or so, and now I'm back to Maxima. The issue I had w/ No-Toil is that it's super hard on the filter (chemically I guess) After a period of time the filters de-laminate, and there's a goo residue on the airbox seal that's a pain to get clean.

For convienence though, No-Toil is hard to beat.

No Toil w/ a Pro Seal :thumbsup:

Been using No-Toil since 2000 and have had Zero problems. Easy clean up and well protected motor. Use a Freezer Zip-lock, insert filter, pour on oil, close zip lock and kneed the oil into the filter. I keep several filters in zip locks, oiled and ready to install.

Twin Air filter and No-Toil oil works for me. I get the oil in the aerosol can, makes it very easy to apply, just wear gloves. Also, the Napalm air filter bolt is a must!

You can also use Oxy Clean to clean the No Toil off the filter. It works great and costs less. You can get a big bucket of the stuff for about 5 bucks..

Good tip yo! :thumbsup:

Twin Air filter and No-Toil oil works for me. I get the oil in the aerosol can, makes it very easy to apply, just wear gloves. Also, the Napalm air filter bolt is a must!

Datz wot I use and do.

I hold mine over the trash bin while I spray.

I've used No Toil on both bikes for over 2 years, the stuff is wonderful. Don't use their cleaner though, Oxy Clean is the same stuff and it's much cheaper, just use very hot water.

Their warranty is awesome too, if you have any issues with your filters, just return it to Lura and they replace them free of charge!

Been using NoToil for Years. Have no complaints yet. The inside of the airbox is always clean from any signs of dust or fine sand. Never see a reason to change. Since its watersoluble, I add the oil when the airfilter is damp. This helps it to soak in uniformly all around the filter.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Similar Content

    • By Kevin from Wiseco
      Jeremy Martin Leads the Charge for Wiseco Riders at Daytona Supercross
      Christian Craig Turns in Career Best in 450 Competition
      MENTOR, Ohio (March 13, 2018) – Jeremy Martin showed the way for Wiseco-sponsored riders in Saturday night’s Monster Energy Daytona Supercross presented by Honda. In a season marred by bad luck and misfortune, Martin put together a near flawless ride to earn his first Eastern Regional 250SX Class podium finish of the season.
      Martin qualified eighth for the division’s annual visit to the World Center of Racing, finished fourth in his heat race, and came home second in the 250SX main event, missing his first win of the year by less than a second.

      “It’s Daytona, a real man’s track.” said Martin who sits fourth in points. “It was the toughest race of the year as far as fitness. I had to slow down a little bit, halfway through the main. I was getting close to (race winner) Jordon (Smith) and I was starting to think about where I could make a move on him, then I made some mistakes and he got away from me. Couldn’t quite get close again, but it’s good. We’re on the podium and in contention for wins again. That’s something I haven’t been able to say in supercross in a while. We want to get wins and now we know it’s coming.”
      Martin’s podium was a bright spot, but the rest of the event was rough for the GEICO Honda/Factory Connection squad. RJ Hampshire crashed hard in his heat race and had to be transported to a local hospital. He injured his back and ribs, but shoulder pain left him with the most concern.
      “I felt good on the bike all day,” said Hampshire via his Instagram account. “Had some pretty good speed and my foot just slid off hitting my shifter in those rollers during that heat race. After seeing the pictures from the crash I’m very thankful I didn’t take a shot to my head. I have some fractures in my T3/T4 in my back and ribs. Also have some damage to my lungs which is why I’ll be spending a couple nights in the hospital. I’ll be getting some more checkups this week on the shoulder also.”
      Cameron McAdoo, the third member of the team, was unable to compete at Daytona after being sidelined with a hand injury two races ago in Atlanta.
      Across the paddock, in the premier 450SX Class, Christian Craig got the call to fill in for Team Honda HRC. With the team’s regular riders Ken Roczen and Cole Seely out with injuries, it was up to Craig to carry the load for the factory team, and the upstart rider didn’t disappoint.
      The San Diego native was solid in both qualifying sessions, won his heat race and snagged the holeshot in the division’s main event. After relinquishing the lead to eventual winner Justin Brayton, Craig continued to show he was up for the challenge. The 26-year-old rider raced for second and third for most of the 20-minute-plus-one-lap feature before losing one more spot in the late goings to bring his No. 32 Honda CRF450R home fourth in the final rundown.

      “I had a great week testing with the team,” commented Craig. “They came down to Florida right after Atlanta and I feel like we really improved. Just getting more time on the bike and getting more comfortable was huge. I started off race day feeling really good. My qualifying position didn’t really show it, but overall I was happy with my riding. It’s all about having fun out there, and man, that’s what I did tonight. I was up front in the heat race, fell to third, but then the two guys in front took each other out so I ended up winning. You can call it luck or whatever, but I just put myself in a good position to capitalize on people’s mistakes."
      “I had a good gate pick and some confidence going into the main. I grabbed the holeshot and led for almost the first lap, but [Justin] Brayton got by me pretty quick. I stayed second for quite a while. I just rode my hardest and did my best. Unfortunately, a couple guys got by me so I ended up fourth. The track was so tough. This is only my second time racing Daytona and last year didn’t go well, so I really wanted to get some revenge this year. It’s better than the week before, but man, I was so close to a podium. I just need to keep putting myself in good positions and work on getting better each weekend.”
      Monster Energy AMA Supercross rolls on this weekend when the series visits the “Gateway to the West” for its annual race at the Dome at America’s Center in St. Louis. The 11th of 17 races on the 2018 supercross calendar will be televised live on FS1 Saturday, March 17, beginning at 8 p.m. Eastern Daylight Time, 5 p.m. Pacific.

    • By desert520sx
      I have a 03 450 that I just got and it runs great! I love my bike and am big on preventative maintenance. I have searched the threads on TT and have not found any descriptive threads on how to check valve clearance or adjust them. Just by looking at them, I can see that the intakes need to be shimmed and the exhaust valves can be adjusted quite easily unless one needs to be adjusted differently than the other.
      I tried to do it last night, and lined up the marks on each side to get the piston to TDC to check adjustments and could not get any readings on tolerances on either the intake nor the exhaust. I moved the crank a little bit forward and got a .011 reading on the exhaust valves. I read in a thread that the spec was .011" for the left one and .014" in the right for the auto decompressor. The spec I am using for the intakes is .006" Are these specs correct? :excuseme:The only issue is that the adjustment for the exhaust valves is one and the same. Different from my KTM where you can adjust each valve individually.
      No matter where the cam was on the intake valves, I could not get any readings. Does anyone have a thread, website, downloadable manual, or article on checking and adjusting valves in these beasts?
    • By Eric Schrader
      I am selling my 2007 Honda CRF 450-R which is set up for desert racing (Track/desert). It has an 18" rear tire with a heavy duty setup (see description for details). The bike screams and has a Tokyo mods carb mod with the 10x ignition mapping (currently set to a handlebar switch for smooth power and max power). Gas tank is a 3.2 gallon IMS dry break tank. V4 steering stabilizer included. Precision Concepts suspention, Bike is set up for 6'4" 175lb rider. Zero oil leaks and well maintained using a preventative maintenance method with the best new parts each time. Receipts for all items can be provided. About 20 hours on the rebuilt head. Carb just rebuilt. Starts cold in just 2-3 kicks. 100% reliable bike as long as you turn the gas on.  Current CA Red sticker and original title.
      Expand above to see details
    • By bigg_stevee
      I recently replaced water pump and seal after I noticed that my '02 CRF450R was spilling coolant on easy trail rides. After the water pump swap (which was successful), I noticed the same problem. It's interesting - the bike only spits coolant (I mean a LOT of coolant) after passing anything above 1/2 throttle. The bike makes this weird 'gurgling' noise, like trying to suck through a straw when your glass is almost empty. This is weird because I properly bled/ burped the radiators with coolant, and filled them to normal operating levels. The coolant spills through overflow hose. 
      anyways - I swapped the radiator because I thought maybe the bike was running hot. I purchased oversized radiators, bought a 1.6 radiator cap (with a temp gauge) and bought engine ice. The bike runs very very cool - the temp gauge allows me to see this. Still, the bike shoots coolant out of the overflow after going above half throttle, making the same weird gurgling noise when it does. Bike has all of its power, top end was replaced not too long ago. 
      I'm lost and don't know what is wrong with the cooling system in my bike. How do I make the bike stop shooting out coolant, and stop making the weird gurgle noise??? Any advice would help me!!! Thank you!
    • By Mxer59
      I have a brand new Barnett Extra plate setup still in the box. It replaces the judder spring with a regular fiber. My old clutch had a judder spring break which wiped out the stock clutch. I was in a bind ordered this kit but it ended up coming 2 days later then it was suppose too. So now I don’t need it asking $180 SHIPPED 
      —“Complete Extra Plate Kit- consists of 8 Kevlar friction plates, 7 tempered steel plates and a set of springs. Provides maximum clutch capacity.”—