hick487

alright guys lets see ur dr's! put up some pics!

2,381 posts in this topic

heres my project so far haha its a 1995 DR250S

l_c7d8a0ba2871cca536c8c8735264c9d3.jpg

ill put up some pics when its done should be soon....:ride:

Share this post


Link to post
Share on other sites

Here's my most recent pic. Not the greatest cause I took it with my cell phone, but you get the idea.

fender2.jpg

2 people like this

Share this post


Link to post
Share on other sites

OK, I'll play along with the crappy cell phone pic.

This is a couple days ago with fresh knobbies looking way too clean.

RightFull.jpg

Share this post


Link to post
Share on other sites
Ok, I'll play. 2008 DR650SM

DSC00911.jpg

That may be the best looking 650 I've seen! It's

a BEAUTY!:ride:;):p

Regards Sonny

Share this post


Link to post
Share on other sites

Hey guys,

I've been trying to figure out how to post photo's. I searched for some info but can't seem to find out how. Can someone point me in the right direction?

Thanks,

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Reply with:


  • Similar Content

    • By Waz Hoare
      Hi, 
      have an 84 pe 175 and really struggling getting the bike to run properly. 
      Carb was thick with crud, so replaced the pilot and main jet, along with the needle valve assembly. Set the needle midway and mix at one and half turns out. Didn’t run great and raised the needle clip up to lean it out, and 2 and half turns on mixture. Runs ok, but does have a flat spot from close throttle to full open and is dumping fuel back into the box and leaving a puddle.  And I can’t understand why. As I said replaced the usual suspects, checked the float and level and all seems good. And although the carb looks good, can’t determine if this worn out, Reed valves or I’m Just being stupid? 
      Any advice would really help, as its doing my nut. 
      Cheers
    • By tilstad
      I have some new rims in sizes 18x2.15 and 21x1.6. This would be inside measurements, flange to flange. 32 spoke holes in both.
       
      They are new, in chrome , good for adding some bling to a modern bike, or restoring an older one.
       
      I listed them on ebay.
      https://m.ebay.com/itm/2-15x18-32-Hole-Chrome-rim-Honda-CRF-others-Japan-made-/272882727078
      https://m.ebay.com/itm/1-65x21-rim-chrome-Honda-CRF-others32-hole-/272882728633
       
      If you have any questions or concerns, let me know.
       
       
       
    • By luke8500
      Hi all,
      Im a little bit smaller of a rider about 5`2 or 5`3 110 pounds.  I feel ive outgrown my crf150rb and am looking to go to a a 250 next spring.  Whats the slimmest/smallest 250f out there. Ive almost entirely ruled out a Yamaha because i went to a dealer to look at them and they feel and look so much bigger than all the other 250s.  Kawasaki seems like its a smaller slimmer skinnier bike but the Suzuki doesn't look bad either.  Ktms seem huge to me and really haven't looked at hondas yet. Any help would be greatly appreciated.
       
      Thanks
    • By KTM_rider_EK_17
      Hi guys, should I buy a YZ125 or an RM125? (between these two below)
      https://tucson.craigslist.org/mcy/d/2003-rm125-price-drop/6289703087.html         (this is the link to the RM) 
      https://tucson.craigslist.org/mcy/d/2002-yz-125/6333183710.html                        (this is the link to the YZ)
      I need more opinions.. Anything would hep and go a long way!