Jump to content
Sign in to follow this  

valves

Recommended Posts

how long can a set of stock valves go??

I really dont want to have to put new vales in my bike:banghead:

is power lost when valves are worn or just reliability?

Share this post


Link to post
Share on other sites

stock is the best way to keep it reliable

i change mine about every 60hrs but it depends on how the bike was rode

ps dont buy the cheep ones like the faction mx .... lasted about 5 hrs

Share this post


Link to post
Share on other sites

Everybody has different times of changing valves. For me around 50-60

But when the bike gets hard to start, thats when you should check your valves. If the bike is losing power, you most likely need a new piston.

Share this post


Link to post
Share on other sites

My son had 130 hours of hard racing on his stock valves and they were still looking good. The seats looked great also.

Share this post


Link to post
Share on other sites

Check your clearances. If in spec, perform a leakdown test and if in spec, no need to replace. If you have shimmed your valves more than once, check the valve for stretch. If yout of spec, replace valve...

Share this post


Link to post
Share on other sites

ive never shimmed just been checked when i had the piston and clutch put in and they were good then

Share this post


Link to post
Share on other sites

My son's kx250f valves never went out of spec the first 130 hours he ran it. I overhauled the top end and he has about 30 hours on it since and still in spec. Kawasaki's just don't go out of spec very often. I can honestly say I don't know a single person that has had an 06-08 go out. I'm sure there have been but I don't know anybody personally. Now the 04-05, that's another story.

Share this post


Link to post
Share on other sites
when you overhauled the topend you put valves in too?

I put in a new piston and rings, valves, springs and collets. Had the valve seats reground.

Share this post


Link to post
Share on other sites

It's good to hear the life that the KXF's are getting.:lol:

How long do valves last? Hmmm? Thats a tough question.Guess it could depend on the size of your wallet or your conscious and how long you want to push things.Valves are good until they close up once.Piston life can determine when you change your valves too since your all ready in there.

How long does a piston last? Well they lose power shortly after their run, 5-10 hrs.Enough to notice? Not for me.50 - 60 hrs for most guy's who race is about right.100 hrs I start to wonder about cracking but hell if it ain't burning oil why fix it.This is where your conscious comes in to play and you start thinking about catastrophic failure.If you last 100+ hrs and go in for a piston you should do the valves and cam chain for insurance.

So we don't race but run the snot out of our bikes in the desert and sand dunes.Not a easy life and a dusty one.I redid the entire top end on the 250 last year(April 08) at 116 hrs With no valve movement or blow by.My conscious got to me.When the bike came apart it still had plenty of life left in them parts. At 191 hrs today, 75 hrs later it's running like a top.How long do we run this time? 130-140-150hrs ? Till something gives Or a valve moves? I start feeling uneasy at 100+. 54hrs on the KXF 450 since April 08.Man time flies when your having fun.That's 4 solid weeks in the desert this year and some day trips.:worthy:

http://www.thumpertalk.com/forum/showthread.php?t=623036&highlight=116+hours

Share this post


Link to post
Share on other sites

Great thread, Ive been wondering the same thing. I too have had that un-easy feeling since 100hrs...at 110 now...no valve movement yet....we'll see...

Share this post


Link to post
Share on other sites
stock is the best way to keep it reliable

i change mine about every 60hrs but it depends on how the bike was rode

ps dont buy the cheep ones like the faction mx .... lasted about 5 hrs

i put faction stainless steel valves and springs in my old crf, they lasted forever never had 2 shim them. i rate them highly

Share this post


Link to post
Share on other sites

I just did top end then on my 09 at 45hrs, all new valves, piston, rings and seats re-cut. All comes down to how you ride the thing i guess. .

Share this post


Link to post
Share on other sites

when i bought my bike the mechanic was friends with the previous owner and said he did a valve job and everything was in spec. supposedly stock are the best valves im just worried because i really dont know how to check them and idk if i wanna tear the engine apart but on the other hand i dont want anyhing bad to happen. My dad and myself plan on doing a complete top end next year with a hi comp piston and possibly valves.

Share this post


Link to post
Share on other sites

we just did a 09 250F 36hrs valves ect and replace the ring aswell piston still good.

customers words valves need doing getting hard to start.

Share this post


Link to post
Share on other sites
we just did a 09 250F 36hrs valves ect and replace the ring aswell piston still good.

customers words valves need doing getting hard to start.

He probably meant valves need shimming.

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Reply with:

Sign in to follow this  

  • Similar Content

    • By Toms.abpg
      Just bought this bike and the pop on decel is horrible, looks like I’m gunna have to try a Tokyo mods remap. Anyone had success with this ?
    • By _Cloudy_
      Hi, I have just bought a kx250f, 2013 with a freshly rebuilt 2016 motor in it, this is my first time on these forums, anyways, I have also bought a lowering link to drop it 4 inches on the arse, I was wondering if anyone knows how much I should drop the forks? 
      I havent put the lowering link on yet. 
      Thanks.  
    • By Zach Miner
      Recently had issues with the original fcr carburator that was installed in my 2009 kx250f, tried jetting multiple time and different gas and the bike would only run with the choke ziptied out. Do I went ahead and purchased the lectron gen 2 4 stroke carburator kit, was kinda expensive and I was kind sceptical but after my first ride all I got to say is wow. The only adjustment I have done it set the idle, the bike runs amazing and feels as if there is more power than before. The kit came with a new throttle tube assembly and a g2 throttle tube with adjustable cams for throttle response. I highly recommend if you have a carburator on your four stroke and don't want to get a new dirtbike that is fuel injection then go the route of throwing out that junk fcr carburator and get a lectron gen 2 carburator for your old 4 stroke

    • By DirtbikeDon
      I own a 2012 Kx250F that I would like to make street legal if possible and I recently saw Rocky mountain I believe sells these battery packs that sit in the airbox for bikes without batteries that looks too good to be true and a headlight and turn signals like a conversion kit basically and I was curious as if anyone has had luck with those or if there junk it would be nice to make my bike street legal for short trips or just have lights for trail riding with friends that already do if possible any tips on converting it? 
    • By kylesmith_14
      The launch control only lights up when you first start up the bike when you try to use the launch control it doesnt light up at all ive tried 1st 2nd and neutral for 3+ seconds ive cleaned the connections and also cleaned the neutral saftey switch or gear selector and still no luck any help would be appreciated
×