2011 Kawasaki Team Green suspension specs


Rider Weight "Fork


(height)*" Spring Rate "Oil


Volume" "Oil

Weight" "Reb

Out" Comp Out Spring Rate "

SAG Level" Reb Out "Clicks

Comp Out Low " Turns Out Comp High Speed "Nitro


KX65ABF Pull Rods

55-65 15mm 2.55 N/mm Light 130mm 10 2**** n/a 46.1 N/mm Light 70mm 2**** **STK 140psi

65-75 10mm 2.65 N/mm Stock 130mm 10 2**** n/a 48.1 N/mm Stock 70mm 1.5**** **STK 140psi

75-85 Flush 2.75 N/mm Heavy 125mm 10 3**** n/a 48.1 N/mm Stock 70mm 1**** 85.3mm 140psi


Up to 75 Std 2.65 N/mm Xtra Light 90mm 5 n/a 8 43.1 N/mm Xtra Light 80-85mm 9 1 150psi

75-100 Std 2.75 N/mm Light 90mm 5 n/a 8 45.0 N/mm Light 80-85mm 9 1 150psi

100-115 Std 2.84 N/mm Stock 90mm 5 n/a 8 47.0 N/mm Stock 80-85mm 8 1 150psi

115-125 Std 2.94 N/mm Heavy 80mm 5 n/a 8 49.0 N/mm Heavy 80-85mm 8 2 150psi


70-85 Std 2.65 N/mm Xtra Light 90mm 5 n/a 8 43.1 N/mm Xtra Light 80-85mm 9 2 150psi

85-100 Std 2.75 N/mm Light 90mm 5 n/a 8 43.1 N/mm Light 80-85mm 9 2 150psi

100-115 Std 2.84 N/mm Stock 90mm 5 n/a 8 43.1 N/mm Stock 80-85mm 8 2 150psi

115-125 Std 2.94 N/mm Heavy 80mm 5 n/a 8 43.1 N/mm Heavy 80-85mm 8 2-3 150psi


135-150 7mm 8.7 N/mm Light L-357cc R155cc 5 16 6-10 47 N/mm Xtra Light 100-104mm 11 8-12 2-3 150psi

150-160 7mm 8.7 N/mm Light L-377cc R175cc 5 16 6-10 49 N/mm Light 100-104mm 10 8-12 2-3 150psi

160-170 7mm 9.1 N/mm Stock L-377cc R175cc 5 14 6-10 51 N/mm stock 100-104mm 9 8-12 2-3 150psi

170-185 7mm 9.5 N/mm Heavy L-357cc R175cc 5 12 6-10 53 N/mm Heavy 100-104mm 8 8-12 2-3 150psi


155-175 5mm 4.7 N/mm Stock +10cc 5 14 8-12 52 N/mm Light 100-104mm 12 10-14 1 - 2.0 150psi

175-185 5mm 4.8 N/mm Heavy 335cc 5 12 10-14 54 N/mm Stock 100-104mm 11 10-14 1 - 2.0 150psi

185-195 5mm 4.8 N/mm Heavy +10cc 5 12 8-12 56 N/mm Heavy 100-104mm 10 10-14 1 - 2.0 150psi

* Fork Height is measured from top of fork tube to top of fork clamp.

** 250/450 Recommended to have the axle pushed back, creating a longer wheelbase for improved stability and traction. This will require a longer chain. Taller riders may not benefit from the longer wheelbase.

**** Stock 86.3mm pull rods on the 2002-2009 KX65 can be exchanged for optional 85.3mm or 87.3mm to raise or lower the seat height by 4.5mm each.

***** Refer to the 2007-2011 KX65 owners's manual for position information.

FOOTNOTES - Rebound and compression adjustments are the number of clicks out from full hard (all the way in). Front fork oil level in millimeters (mm) is a measured distance or in cc's for a measured volume. Rear shock sag level is measured

in millimeters (mm). All optional spring part numbers can be found at your local Kawasaki dealership.

SPECIAL NOTE - Team Green recommends that any suspension sag measurements be done when shock is cold. Always test new setting before racing.

N/mm = Newtons / millimeter - Kgf = kilograms force

Conversion Formula for each method of measurement: N/mm Spring Rate x 0.102 = Kgf/mm Spring Rate and Kgf/mm Spring Rate x 9.807 = N/mm Spring Rate

*Team Green Specifications subject to change.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Similar Content

    • By Chris Edwards
      Hey guys, I'm wondering what suspension settings you all are running front and rear?  I have a 2017 crf 250r I'm a 210lb newer rider, my settings are currently set at,
      rear suspension low speed  at 12 clicks
      rear suspension high speed 2 turns
       rebound is 12 clicks.
      Left front fork inner chamber 150psi, outer  chamber 10psi, balance pressure 150psi
      Right front fork compression position 7 clicks, rebound 29 clicks
      Sag is 4"
      Thanks guys
    • By Stillwell Performance
      One of the most common calls we get here at the shop is “how do you recommend I go about tuning my suspension?” Good question! The second most common call is “I started turning clickers on the front/back/bottom/top etc. and now I don’t know what I did, help!” The amount of improvement you can gain from proper suspension setup is significant, if you go about it in the right way.
      Look at it this way: if you are 6ft. tall and get in your truck after your 5 ft. 3in. wife just drove it, the first thing you are going to do is adjust the seat/steering wheel, etc. for your size. The same thing goes for your bike’s suspension-last week we had (3) 2010 bikes in the shop for revalves at the same time. Identical models, one guy was a 150lbs. pro racing MX, the next guy was a “B” level GNCC racer and weighed 220, and the third guy was a 180lbs. trail rider. Same bike, three totally different setups!
      So with that in mind, here is where to start:
      • Grab your owners manual, a computer, clipboard and a scale. You cannot effectively start tuning until you determine if the correct springs (fork and shock) are on the bike for your weight. Put down the double cheeseburger, hop on the scale, and get your weight in street clothes. Add in for your gear, which typically runs between 20-30lbs. You can easily check recommended spring rates by visiting www.racetech.com under their spring rate calculator. Look in your manual (or ask your tuner) and see what rates are on the bike.
      • If you need to change spring rates-do it first. Trust me on this, trying to tune suspension with the wrong rates is not only frustrating, but you will be short changing yourself on the results. On most bikes the shock spring is easily changed, fork springs can be a bit more difficult-get qualified help if you need it.
      • Even if you are familiar with what “clickers” are, take a moment and read your manual. Determine what style of forks you have (closed cartridge or open cartridge), where the compression and rebound clickers are, and check to see if your shock has both a high speed and low speed compression adjustment.
      • Grab the right tools to adjust, load up and go find a typical piece of terrain to test on. By typical I mean your MX track, hare scrambles course or favorite singletrack. You don’t need to ride a 30 mile loop in order to adjust your bike, rather focus on finding a section of track/trail that has all the different types of jumps/bumps/whoops you encounter.
      • OK here is where I will preach a bit-everybody has a buddy or two that claims to “know suspension” and setup. This is YOUR bike, and unless you plan on dragging him around on the back of the seat the end result of your tuning should be focused on what feels good to YOU. Trust the feedback the bike gives you…..
      • SET YOUR RIDER SAG!!!!!!! This is critical to tuning properly. Again, look in your manual or ask your tuning dude.
      • If you do not have an idea of where to set your clickers, put them in the middle of their adjustment range. This is your baseline setting.
      • Gear up and get warmed up. It is important to be loosened up on the bike BEFORE you start tuning, or you run the chance of mis-diagnosing how the bike is feeling (I never start testing until I have at least 15-20 minutes of warmup time on the bike-I always ride stiff initially and sometimes do not get into a groove until then). Some guys can just jump on and pin the damn thing right from the truck. You know who you are, Wattsy……
      • Remember, this is a tuning session not the MXoN. Use you head and ride at a pace UNDER you max speed-there will be plenty of time to “fang it” once you have zeroed in on some good settings.
      • OK-ride and get a good feel for the bike with the clickers in the middle of their range. Now it’s time to really find out what “too soft” and “too hard” means.
      • Take your clickers and turn them all the way out, full soft. Go ride the bike, but take it easy-it will feel ALOT different. Then come back in and turn everything all the way stiff-go ride again, being careful as this will feel totally different again. For guys that have tuned a bit, these two steps might seem pretty basic, but you will be amazed at the difference in how the bike feels. This is especially helpful for guys who are just starting out.
      • Set everything back to baseline. FROM THIS POINT ON YOU WILL ONLY MAKE ONE ADJUSTMENT AT A TIME!!!!!!
      • So now you will want to determine your tuning range. The tuning range is what settings you will use to adjust for different conditions. For example, If you are an MX racer as well as an occasional singletrack rider you will want to use different settings for those conditions.
      • Fork compression is a good place to start. Ride your test section at baseline, then go about 3 clicks softer. The question to ask yourself after each adjustment is: Does it feel BETTER, WORSE, or THE SAME????
      • There are no right and wrong answers, only what you feel. So let's assume that the 3 clicks softer felt better-go 3 more clicks softer each time until it does not feel as good. You have just found the soft end of your fork compression tuning range. Now return to baseline and do the same thing, only this time go stiffer. After you have found the best compression setting, work on rebound. Remember, one adjustment at a time ONLY or you can become confused!!! Do the same testing with your shock. Once you have both comp and rebound individually adjusted, you can fine tune them to work together-just make one adjustment at a time!
      • As a final test, when you have what you would consider your best setup, write it down, then go back and compare that to your initial baseline, riding both setups back to back. Might surprise you…….
      I could go into some advanced tuning topics about the interrelation of compression/rebound, high and low speed comp, tuning for extremes, etc. but we will save that for another newsletter. Take your time, tune by how your bike feels to you and have fun. You will be surprised by how much better you will ride with well adjusted suspension.
      You can learn more at www.stillwellperformance.com
      KEEP IT PINNED!!!!
      Alan Stillwell

    • By Jo_nathan
      Selling the showa A kit off of my yz250. It comes with a set of like new x trig adjustable triple clamps. Have 4 rides on rebuild and overall in great shape. Few dings, no dents or leaks. Setup for a 165lb a rider. Work absolutely awesome! I got hurt and cant ride for a year so I'm selling off some of my parts. 
    • By Kim Franz
      lookin to upgrade my suspension on my 06 cr250, curious whats possible with some work.
    • By tplayer100
      Currently have a 2000 drz400s work stock suspension. From my understanding this is the worst suspension the drz ever came with without even rebound damping adjustment. Therefore I'm looking for a upgrade. I'm seeing three approaches to take. First being a newer year s model suspension with dampening adjustment. A SM model USD forks and triple tree or some USD forks and triple tree from a rmz. So if you were going to upgrade what direction would you go. I currently ride off-road mostly but I do have some 17s for on road with as well so have to keep that in mind. Thanks