Jump to content
Sign in to follow this  

fuel screw adjustment

Recommended Posts

to add...

Fuel Screw/Pilot Jet

Fuel screw settings in the 'book' are recommended starting points. Every bike is different, as is the temp and altitude. Set the screw according to this method. Do it with the bike fully heated up.

Gently turn the screw all the way in. Now back it out two turns. Start the bike and fully warm it up, go for a 10 minute ride. Set the idle to speed to 1,500~1,800 RPM as best you can (I know, without a tach this is tough, just set it to were it idles relatively smoothly). Once warmed, slow the idle to the lowest possible speed.

*** When turning the fuel screw, keep an accurate 'count' of the amount you are turning it and record it in case you have to reset it for some reason. Makes life easier when you can just set it from notes Vs. going through the procedure again.***

Turn the screw in until the idle becomes rough or the bike stalls.

if it stalled, open the screw about 1/4 more turn. Restart it and slowly screw it in till you can just perceive a change.

If the screw can be turned all the way in and the bike still idles perfectly and does not stall, then you need to go down a size in pilot jet.

Now very slowly, open the fuel screw till the idle is smooth. Blip the throttle, let the bike return to an idle, wait say ten seconds. Confirm it is the same smooth idle.

If the screw has to be opened more than 3 turns to get a smooth idle, you need to go up a size in pilot jet.

If you find it does not stall with the larger jet but has to be open more than three turns with the smaller pilot jet, put the larger one in and set the fuel screw at 1/2 turn.

If the idle speed increased, adjust the idle speed knob to return the bike to a real slow idle speed. You must then re-visit the fuel screw. Keep doing this till the fuel screw is opened just enough to provide a nice steady idle at the lowest possible RPM. Once this is done, increase the idle speed to the normal one for your bike, typically about 1,800 rpm, but go by the spec in your manual.

Share this post


Link to post
Share on other sites
to add...

Fuel Screw/Pilot Jet

Fuel screw settings in the 'book' are recommended starting points. Every bike is different, as is the temp and altitude. Set the screw according to this method. Do it with the bike fully heated up.

Gently turn the screw all the way in. Now back it out two turns. Start the bike and fully warm it up, go for a 10 minute ride. Set the idle to speed to 1,500~1,800 RPM as best you can (I know, without a tach this is tough, just set it to were it idles relatively smoothly). Once warmed, slow the idle to the lowest possible speed.

*** When turning the fuel screw, keep an accurate 'count' of the amount you are turning it and record it in case you have to reset it for some reason. Makes life easier when you can just set it from notes Vs. going through the procedure again.***

Turn the screw in until the idle becomes rough or the bike stalls.

if it stalled, open the screw about 1/4 more turn. Restart it and slowly screw it in till you can just perceive a change.

If the screw can be turned all the way in and the bike still idles perfectly and does not stall, then you need to go down a size in pilot jet.

Now very slowly, open the fuel screw till the idle is smooth. Blip the throttle, let the bike return to an idle, wait say ten seconds. Confirm it is the same smooth idle.

If the screw has to be opened more than 3 turns to get a smooth idle, you need to go up a size in pilot jet.

If you find it does not stall with the larger jet but has to be open more than three turns with the smaller pilot jet, put the larger one in and set the fuel screw at 1/2 turn.

If the idle speed increased, adjust the idle speed knob to return the bike to a real slow idle speed. You must then re-visit the fuel screw. Keep doing this till the fuel screw is opened just enough to provide a nice steady idle at the lowest possible RPM. Once this is done, increase the idle speed to the normal one for your bike, typically about 1,800 rpm, but go by the spec in your manual.

Follow William's advice :lol:

Share this post


Link to post
Share on other sites

thanks for the info guys. mines at 2 1/2 turns and wasnt sure if that was to much. getting ready to install one of the adjustable fuel screws so i dont have to try & get a screwdriver up in there or roll the carb everytime to adjust it.then i can start to play with it more i just needed a starting point & what to look for.

Share this post


Link to post
Share on other sites
thanks for the info guys. mines at 2 1/2 turns and wasnt sure if that was to much. getting ready to install one of the adjustable fuel screws so i dont have to try & get a screwdriver up in there or roll the carb everytime to adjust it.then i can start to play with it more i just needed a starting point & what to look for.

One of the best mods you can do!!

Share this post


Link to post
Share on other sites

If you don't get the accessory screw, then you can use a hex screwdriver bit to adjust the fuel screw. You know the ones, that you see at the hardware store checkout counter for like $.75 each. You can use that to reach up in there without twisting the carb sideways.

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
Sign in to follow this  

×