Jump to content

gasgasser

Members
  • Content Count

    469
  • Joined

  • Last visited

About gasgasser

  • Rank
    TT Bronze Member

Profile Information

  • Location
    New Zealand

Recent Profile Visitors

The recent visitors block is disabled and is not being shown to other users.

  1. gasgasser

    2018 KTM 85 odd sag recommenation

    Thanks for that we'll aim for 30mm and 120mm. Just one more question the manual has the high speed compression as softer the further it is wound in, I've not seen this before as it's normally the other way round. Did you find this to be accurate?
  2. gasgasser

    2018 KTM 85 odd sag recommenation

    Did you ever sort this out on the bike? The sag measurement seem way off with 120mm rider sag. The bike does not feel balanced
  3. gasgasser

    how to bring back a drowned xc-f

    Yes it is FI. No I have no idea either. Would be good to know as many of the enduros and races I do have river crossings
  4. gasgasser

    how to bring back a drowned xc-f

    what about draining the water out of the carb?
  5. gasgasser

    how to bring back a drowned xc-f

    I haven't drown my bike, maybe I should of been a bit clearer. If I drown (water through air filter) my bike on a ride/race what do I need to do at the side of the track to get the bike running again?
  6. If I drown my 2013 250 xcf by completely submerging it under water how and what would I have to do to get it back running again? I know what to do with a 2stroke but not this bike.
  7. Tye, can you describe how to line up the timing marks on the cams for you bike, currently rebuilding the same model as yours and the timing marks are very different to the previous model. I have no manual so wanted to check this. Thanks
  8. I managed to suck water through my 13 250 xcf today. The bike started to run really bad and I had to stop riding. It would not rev high, and kept dying. I guess the bottom end will just need flushing until it is not milky, but I'm a little confused as to what to do with the carb and the fuel injection system. Can anyone tell me what I should be doing to get the bike up and running again.
  9. I have a 2013 250 sxf that has just over 30hrs on it. Today I took it for a ride at the track and noticed it was popping when backing off. This was mainly after being hard on the gas in third. I haven't noticed it doing this before, does anyone have any ideas why? I would of thought this would not be the case on a FI bike?
  10. gasgasser

    GasGas 250 txt pro suspension set up

    Should there be a free sag and rider sag measurement range?
  11. I have just brought a 07 gasgas 250 txt pro to have some fun on. I don't have a manual and was wondering what the sag settings should be on the suspension. Also a guide on tyre psi would be good too.
  12. gasgasser

    13 250 xcf heavy clutch

    That's not really a sensible answer. I've worked as a carpenter for the last 15yrs so hand strength is not the problem and squeezing a tennis ball will not improve a bikes clutch feel. The bike seems to have an excessively heavy clutch for a 250f, and coupled with the horrible brembo lever, I don't like it. I like to have it set up just right so feathering the clutch is no problem to do weather its at the start of an enduro or 5hrs in when things are tricky. I do have a Midwest lever, but the rod is too long, maybe I'll get a shorter rod. I was thinking more a long the lines of swapping the springs of another model.
  13. gasgasser

    13 250 xcf heavy clutch

    could you change the springs?
  14. I recently brought a new/leftover 13 250xcf. Man the clutch feels heavy on this bike, so much so it kind of spoils it for me. Has anyone else found this, or know of a way to reduce the pull?
  15. gasgasser

    Rekluse core exp 3.0

    Whats actually changed??
×