Jump to content

eauxgod

Members
  • Content Count

    95
  • Joined

  • Last visited

About eauxgod

  • Rank
    TT Member

Profile Information

  • Location
    Louisiana
  • Interests
    MTBing, DBing, SHOOTing
  1. eauxgod

    predator exhaust

    Whatcha got?
  2. eauxgod

    Louisiana Hammond LA

    Is there a place in Hammond where a quick test ride is possible. I am meeting someone with a quad for sale and I want to be able to ride it. Thanks!
  3. I have a mint (300 miles) stock '03 DRZ400E with a few aftermarket things (not performance) that I may trade even for a lightly used totally stock '06 LTZ400. Do you guys think this is a good deal? Can you get to the spark plug without removing anything on the LTZ? Does the LTZ's engine/clutch/final drive have the same issues as the DRZ's like the water pump leak, the need of MCCT, etc.? Are the optimal sea level jetting specs the same as a DRZ400S? What else should I look at to ensure the bike's condition? Thanks!
  4. eauxgod

    C'dale X440S - Brand New

    Thats how much I was gonna sell the front shocks for...
  5. eauxgod

    C'dale X440S - Brand New

    I found a NOS '02 X440S for 3.5k. Good deal or should I pass? Possible part out? Just curious... Also, what is the difference between the x440 and x440s? Thx
  6. eauxgod

    E Gas Tank - Lower Mounts Too Wide?

    I guess that is what happened at some point but not sure how or when... I ended up using a .5" nylon spacer on each side and slightly longer M6s, but next time I need to yank the tank I will follow your advise. Thanks
  7. I don't remember the lower mounts on the tank being so much more wide compared to the frame mounts...what gives? Do I just force the tank's bottom mounts inward flush against the frame mounts even if there is almost a 3" gap? It seems like that really would bind the tank and stress those mounting tabs too much. Is there something I'm missing? Thanks.
  8. eauxgod

    Baton Rouge - Where to get FCR jets?

    Is it possible anyone whould have them in stock?
  9. eauxgod

    FCR Slide Plate done after 30 hours?

    Damn... The bike sat for year so I took the carb out after I could not get it to idle well. The carb did not look too bad but I still cleaned it w/ brake cleaner and comp air and re-jeted per the forum (160/48/5th/2trns). The bike ran like crap so on the third carb removal and cleaning I decided to take the slide out and it had crap between the plate and slide along with those chunks missing. Double Damn... So if ran this weekend would I just have idle issues and maybe some bogging? Thanks, I appreciate the info.
  10. eauxgod

    FCR Slide Plate done after 30 hours?

    So these little chunks of seal ring missing are ok for now?
  11. eauxgod

    FCR Slide Plate done after 30 hours?

    That's just the angle the pic was taken... Do I need to replace either right now? Thanks, Eddie!
  12. My bike is a 2003 KLX400R (xtra fast DRZ400E) with OEM fcr and only about 30 hours of use. slide plate gasket: back of plate - teflon like coating is coming off: Are they done? Is that gasket causing my bike to idle only with the choke?
  13. eauxgod

    Baton Rouge - Where to get FCR jets?

    I ended up getting them from RAD and HD...thanks though! I don't guess you have a surplus of slide plate gaskets
  14. My bike is a 2003 KLX-R with OEM fcr and only about 30 hours of use. slide plate gasket: back of plate - teflon like coating is coming off: Are they done? Is this normal? Would the gasket be the cause of a "choke only" idle? I have a camping/riding trip this weekend and I doubt that I can get a gasket before then...
  15. eauxgod

    Carb off, now what?

    Thank you, Sir! Your help is appreciated tremendously; researching/finding the correct parts has been a pain. Regarding the Keintech, was there enough room for it above the starter? Thanks again!
×