Jump to content

George R Decker Jr

Members
  • Content Count

    13
  • Joined

  • Last visited

About George R Decker Jr

  • Rank
    TT Newbie

Profile Information

  • Gender
    Male
  • Location
    New Jersey

Recent Profile Visitors

The recent visitors block is disabled and is not being shown to other users.

  1. George R Decker Jr

    01 ktm 250 exc hydraulic clutch

    So I got the clutch feeling great at the handle I can see motion at the basket I think I just need to ride it and it will free up I got it warm and kept pumping it and it free'd up I vacuum bled it before hand and noticed a difference the bike was sitting with no fluids apart for some time so I think I just need to truck it to were I ride now and putt it around and see if it frees up the rest of the way thanks for the responses
  2. George R Decker Jr

    01 ktm 250 exc switch to a 2003 front forks?

    Thanks guys guys I will just have to give in and have the fork seals replaced
  3. George R Decker Jr

    01 ktm 250 exc switch to a 2003 front forks?

    Hey does anyone know if the front forks off a 2003 250exc will go right onto my 01 250 exc? I found a set that was swapped right away that will be cheaper to purchase than changing the fork seals in mine.. part numbers are different but I'm learning with these bikes that doesn't mean much. I want to just be able to bolt it up and use my original rim the whole bit or I wouldnt see it worth it anymore
  4. George R Decker Jr

    01 ktm 250 exc hydraulic clutch

    I soaked them while they were out of the bike and tried to run it to free it up unfortunately I have to trailer my bike to be able to ride it I have no yard and maybe 75ft of driveway lol but I'll try it again tonight after work. I'm about beat with it and thinking of sending it to a shop which of course I dont really have the money to do
  5. George R Decker Jr

    01 ktm 250 exc hydraulic clutch

    That's why I tried the trans fluid with it. But now I had the clutch plates out of the bike so if that were the case it should be def free by now
  6. George R Decker Jr

    01 ktm 250 exc hydraulic clutch

    Hopefully someone here can help me I bought this bike and it was in pieces this is my final step before I can ride and its driving me nuts to the point I'm almost ready to sell it. I have an 01 ktm 250exc I have purchased a new slave cylinder for the bike hooked it all up I gravity bleed the system until fluid came out closed the bleeder filled the reservoir pushed the piston on the slave until no bubbles came out anymore I then proceeded to bottom bleed a few times just to make sure. My handle feels weird like there is resistance yet with the clutch cover off I can see movement. I have taken the clutch out inspected the basket filed anything that could possibly give it any problems still nothing I ran it with trans fluid in it to try to free it up incase it was stuck still nothing. I have a lot of time and money in this bike and I am really started to wish it came stock with a cable clutch does anyone have any suggestions?
  7. George R Decker Jr

    01 ktm 250exc clutch slave

    Thank you for the response you just confirmed what I thought I had been looking at a slave for a few days obereon and it looked identical but someone on another thread I'm on had it for there bike and it had a different hose hookup so I wasnt sure but after you said it to I'm trying it and I ordered it has the same part number you posted thanks again mine is beyond rebuilding it has metal shavings
  8. George R Decker Jr

    01 ktm 250exc clutch slave

    Hey guys I'm running into a problem my slave cylinder is shot and discontinued I was wondering if anyone knew what options I have for a slave cylinder I cant find the exact one anywhere only thing close I have found is an obereon clu 1201 but apparently the hose hookup is different if anyone has gone through this and knows what I can do I could really use some help
  9. George R Decker Jr

    93 rm125 carb questions

    Another topic on my rm125 project. I finally have my bike rideable. However it is to rich and plug's are expensive for this bike. I have stock jetting with a FMF gold series pipe and shorty spark arrestor. The needle is set halfway. I was considering dropping the needle down one knotch to lean it out but I was wondering if anyone else has gone through this problem and had any suggestions. Thanks in advance
  10. George R Decker Jr

    93 rm125 twist throttle

    Haven't seen one yet
  11. George R Decker Jr

    93 rm125 twist throttle

    Hey guys another problem has surfaced on my 93 rm125 project this should be my final problem although it seems to be way larger than it should be. So I got the bike with an aftermarket motion pro twist throttle and some sort of universal cable I am unable to find. The tube was broken in the throttle so I bought another motion pro after attempting for 3 weeks to go OEM which is no longer an option die to price and back order. I have the stock cable new which will not go into the motion pro I have as the adjuster threads are way too small and the aftermarket cable seems to be just a little to high even when all adjusters are in the carb does not close. I apparently need to find a whole kit that will def work with my bike I have come across kits on Ebay that say they will but when I Google the part number the manufacturer says it will not. Has anyone else overcome this problem and know of a non $300 solution for me?
  12. George R Decker Jr

    93 rm125 rear brake lever return spring

    Thnx man appreciate it hopefully with that info I can somewhat safely rip through the woods tomorrow.
  13. George R Decker Jr

    93 rm125 rear brake lever return spring

    Hey guys I bought a 93 rm125 pretty much rolling chassis I have it pretty much assembled but I am looking for someone that could possibly measure the rear brake pedal return spring on their bikes so I can go to Lowe's to get one that's what my local parts shop told me to do otherwise I have to wait 2 weeks for Suzuki to deliver it and I would like to take it out tomorrow also a pic for reference would be awesome thnx in advance
×