Jump to content

tHEIF_oF_dREAMS

Members
  • Content Count

    21
  • Joined

  • Last visited

About tHEIF_oF_dREAMS

  • Rank
    TT Newbie
  1. tHEIF_oF_dREAMS

    CRF fork seals

    I need help on seperating the forks so that I can replace the oil seals. This is my first Honda and they are different than the Yamaha's. Cant seem to get them apart. Any help you can offer would be a great help. Thanks for the input!
  2. tHEIF_oF_dREAMS

    00 YZF 426 hot starting problem....

    James D, very sorry for the misunderstanding, and thank you very much for the clarification. we are performing the changes now and hope to get some test time in before the dune trip on Wednsday! Thank you JD and all forum members for helping us out! T
  3. tHEIF_oF_dREAMS

    00 YZF 426 hot starting problem....

    What is the proper proceedure for setting floats. I have read of two ways but they seem to differ from each other. JD had mentioned that the level should be at 2-3 mm. Any help will be greatly apprciated. thx again for the forum help!
  4. tHEIF_oF_dREAMS

    00 YZF 426 hot starting problem....

    James, we will look at each of this as you listed them. We were running a 168 main but she was back firing on decel. I am not sure how to set the floats. clip 3, (from the top?)My partner thinks that the spark plug could be suspect, he is a 2-smoke fan and wants to change the plugs alot. I told him its a different beast all together. We also tried the blue wire cut ( per motoman393 )the valves are within wr specs. we did notice that if you turn the gas off and let it run for bout a minute then turn the bike off she will start again. Thanks again for all the support with our problem. T
  5. tHEIF_oF_dREAMS

    00 YZF 426 hot starting problem....

    I will def check the hot start. Its after market thumb switch. What is or where may i find the valve clearanve spec for the YZF. i have a shop manual for the WR same year but i dont believe that they are the same. Thx again.
  6. tHEIF_oF_dREAMS

    00 YZF 426 hot starting problem....

    172 main, clip in center of needle ( 4th from top), 42 pilot, 1.5 to 1.75 tuns out (ish) on air screw. Bk mod bout .3 on the squirt. She will start cold with 3 kicks every time, after shes warm and you stall her, heartless beast. Thanks again for any help or light!
  7. Just got this bike used pretty hard, was raced hard. Not horrible shape. We have been messing with the tuning, Bike will start 1 to 3 kicks dead cold every time. run for a while stall or stop bike, 30 - 40 kicks min to re fire. Hot start, gas off tried many different combos. We did the Bk mod and we run race gas for the port and polish in the motor. When she fires, it a running machine. Tuned for desert in PHX, bout 1000 to 1200 ft. Plug seems fine, nice golden brown. Could the floats be flooding her? Ant help would be greatly appricated!
  8. tHEIF_oF_dREAMS

    WR 426 / what plastic would fit on it.

    Acerbis is a great site! Just got new pastic for my 00 WR, careful though, my shrouds came in and they are for the YZ. not horrible fit but with a slight mod to make them work.
  9. tHEIF_oF_dREAMS

    WR 426 / what plastic would fit on it.

    Acerbis is a great site! Just got new pastic for my 00 WR, careful though, my shrouds came in and they are for the YZ. not horrible fit but with a slight mod to make them work.
  10. tHEIF_oF_dREAMS

    why woundn't my wr start

    I have 00 wr and caused myself months of sufferen cuz I had screwed around with the carb and unknowingly destroyed the carb joint between back of motor and carb. This $11 part is sensitve to your its clasp. Hope you find it! t_o_d
  11. tHEIF_oF_dREAMS

    why woundn't my wr start

    I have 00 wr and caused myself months of sufferen cuz I had screwed around with the carb and unknowingly destroyed the carb joint between back of motor and carb. This $11 part is sensitve to your its clasp. Hope you find it! t_o_d
  12. tHEIF_oF_dREAMS

    Bike won't remain idling, just dies

    I had a very similiar problem with my 00 wr400, but I had many probs, the biggest prob was my carb joint (the thingy between carb and motor)was worn and not seeding the carb well and was screwing me up pretty good. replaced that for 11.85 and bike idles great! Never hurts to check! Good Luck! t_o_d
  13. tHEIF_oF_dREAMS

    Exhaust pipe envy

    The pipe itself is in very working shape, just looks pretty poor. Iam stil waiting for a return call from spray guy, its the e-series w/12disc, the emblem got ripped off on a nice endu I must say, I have paid my gravity bill and spending more quality time riding so I am slowly trying to undo my damage but have to keep budget in tach or wife will kill. thanks guys for the help! t_o_d
  14. tHEIF_oF_dREAMS

    Exhaust pipe envy

    Thanks Chaindrive, awesome ideas my friend I actually have a connection for powder coating, I think that I will give him a call! Thanks again t_o_d
  15. tHEIF_oF_dREAMS

    Exhaust pipe envy

    Hey a shout out to you crafty guys, is to possible to paint an after market pipe? After ample ground time if you will have some nice scratches and dents, then tried to buff out and really f'd up the thing. Any help would be awesome thanks!
×