Jump to content

Roger M

Members
  • Content Count

    442
  • Joined

  • Last visited

About Roger M

  • Rank
    TT Bronze Member

Profile Information

  • Location
    Virginia
  1. Roger M

    Question about repairing an air filter.

    Don't use gas! Clean your filter with kerosene to strip most of the oil, then wash it in very warm water and laundry detergent to get out any remaining dirt. Even if you have to re-glue some areas after cleaning the filter, the important thing is that the foam is sealed to the rubber ring when the filter is re-installed in the airbox. It's not a perfect solution, but it beats buying new filters all the time.
  2. Roger M

    motor oil

    Use Honda HP4M in hte crankcase, and GN4 in the tranny--both 10-40W. Overfill the tranny slightly to 825-850cc.
  3. Roger M

    Improved Horsepower

    Forget all this with the cams---the stock X cam is best for valve life--if you want more power EVERYWHERE and all you can handle, get a high compression piston and run VP U4.4 oxygenated race fuel.
  4. Roger M

    Suspension Linkage Bearings

    My advice would be to stick with the OEM parts. They may cost more, but they are top quality. Find a dealer, online or otherwise who will cut you a break on the price. Don't go for cut-rate with bearings--that's for plastic and other non-critical stuff.
  5. Roger M

    Big Bore vs High Comp Piston

    I've not used a big-bore set-up, but for racing applications, I have used the JE high compression piston for 3-1/2 years and am very pleased with it. It provides a nice boost everywhere and still allows the engine to rev-out like stock with proper jetting and air-box mods. I don't scream it--don't have to--she runs like a scalded-dog. I also use oxygenated race fuel which isn't necessary with the HC piston, but the two seem to go together really well.
  6. Roger M

    Rear Sprocket for Hare Scrambles

    I prefer the stock, which is 53, if using a knobby--they tend to slide and spin some. If using a trials tire, a 54 works better--makes 2nd gear a bit more usable in tight woods sections.
  7. Roger M

    Question about repairing an air filter.

    This happens to the OEM filters, usually about the 3rd time its cleaned, no matter what oil or cleaner is used. I have several, and have repaired them all with Shoe Goo from Wal-Mart. It works reasonably well if you make sure the filter is totally clean of any oil and completely dry before applying the glue. Allow the glue to set for at least 24 hours before using the filter. If done properly, it generally doesn't come apart in the same place again.
  8. Roger M

    Gearing down a CRF250X

    You can use a larger rear sprocket than stock without issues with the chain guide if you add 1 link to the chain--this moves the axle back enough to provide clearance. I am currently using a 54 rear, which is available from Honda. Note that a 14 tooth front sprocket is the largest that will go on and clear the swingarm.
  9. Roger M

    suspension/springs

    I think for your weight, which is about the same as mine, these settings will be harsh unless you ride very aggressively. With the stock valving, I would soften the fork compression 3-4 clicks, soften the shock hi and low compression by about 1/2, and I would use the stock fork springs which are .42 and go to a 5.0 shock spring or at most a 5.2
  10. Roger M

    04 CRF250X acceleration problems

    One other thing--check that the vent in the gas tank cap is not clogged--that would cause it to behave in a similiar fashion to what you describe after a few minutes of running normally.
  11. Roger M

    04 CRF250X acceleration problems

    The wiring to the clutch lever only involves the starter motor, not the ignition--my guess is the problem occurs when load is applied to the engine and pulling in the clutch relieves the load. I would check your carb's accelerator pump for proper function--with the carb off the bike, a significant squirt of fuel should be immediately visible from the AP nozzle in the carb throat when the throttle is twisted. If not, flush-out the tiny passages in the AP cover and up in the body of the carb with carb cleaner and compressed air, and examine the pump diaphram for signs of damage. Also, if you don't have the "O-ring modification" to the AP link lever, you should do so--the extra force from the o-ring makes a huge improvement in accererator pump function. It wouldn't hurt to double-check your valve clearances, and give your ignition wiring a once-over looking for loose connections--maybe check the kill-switch wiring for shorts against the handle-bar and steering-head.
  12. Roger M

    Accelerator pump issue

    Make sure all the little holes in the AP cover are unrestricted by dirt/debris--blow through with carb cleaner and compressed air. Also check the passages in the body of the carb that lead to the AP nozzle. Not too likely any problem with the diaphram, but I did have one become sortof curled-up, so I replaced it. My AP became non-functional for reasons still undetermined, but the O-ring modification to the link-lever corrected the problem and made it work better than ever.
  13. Roger M

    FMF silencer

    The Powercore is about the same as stock but with a bit more pleasant tone to it--I use it racing hare scrambles without any issues. If you are using a powerbomb header, that might bring the sound level down some.
  14. Roger M

    What fork oil level do you run?

    Fork fluid level doesn't have any impact on fork action until you reach the last couple of inches of travel--at that point, the change in fluid volume produces a change in air-spring effect. Adjust your compression clickers to a softer setting--when I went to stiffer fork springs I had to go down to 6-8 clicks from full soft. Roger M--04 X
  15. Roger M

    OEM or aftermarket fork seals

    Use OEM--they're the best. I've heard of many situations where other brands didn't hold up or leaked right-off. One of mine on my 04 is actually the original one that came on the bike and it doesn't leak significantly after 4 seasons racing--you can't beat that kind of durability.
×