Search the Community
Showing results for tags 'Floatseat'.
OK here goes... Picked up an 04 200 EXC few months back, needed some work to say the least, wont go into detail of all the things i've fixed on the bike just the current and most present issue I cant seem to fix... it is smoking IE blue smoke/lots of splooge to the point that at the end of a few hour's ride, it's out the tail pipe, running down the back and dripping onto the swing arm/rear break caliper and blue smoking quite a bit. When I first got it, it smoked more and smelled like shit. So first things first went to the carb, I live on the Oregon coast (elevation/temp reference) it's old dirty/stained but inside looks good, came with jetting pilot-45, main-178 needle: no idea what brand guessing stock in the 3rd clip, adjusted the float height due to it leaking gas when bike was upright no tilt with the gas on, Bought JD jet kit and running pilot-45, Main-185 and Needle is blue 3rd clip (JD's recommend specs for my bike @ my attitude). I have also replaced my Inner crankcase seal twice (First time I thought I messed up the O-ring so redid to make sure). I've rebuilt the top end/new piston (same thing) cleaned the PV, NOTE HERE that the PV has some issues, it seems to work fine but the screw that goes on top of the cylinder, down into the PV/flap would not come out preventing me from removing the flap to clean it, however it move's/ function's correctly, and has minimum clearance on both sides. One of the PV cover bolts that also works at the exhaust spring holder, was over torqued at some point (impact driver prob), or a result in a hard impact, the hole the bolt goes into is flailed/jared open a bit, not bad, not in the way of any function/ PV Gearing/hinge, it is not needed for that area to be air tight as their is also a breather that goes out of the PV so will not result in an "air leak" or loss in Top end PSI.... anyway... it's still smoking.... quite a bit.. now the bike itself rides fine I feel, the carb does puke gas when tilted over slightly/ hard to start (kick start) after flooded (like all bikes tho) I don't have any stalling/low idle issues outside of user error on clutch control. Honestly outside of it smoking as much as it does I would think nothing is wrong with it.. I have also tried raising the needle Clip to 2nd clip and it changed nothing at all, not even feel of the bike/response and have a new Spark plug I have yet to put on the bike. I have also "compromised" the crankcase Gasket (new one in the mail) while I was putting the Crankcase back on but that should do nothing with the exhaust just a little gear oil leak not relevant but throwing it out there. So I am at a loss... I've been toying with the idea of getting a Lectron carb... However... would hate to drop $400~$500 and the issue still persist, if it's a jetting/carb/float issue that would fix it and improve MPH/fuel consumption Or something with the PV? but I don't see the PV causing that much smoke/sploogee... I've ridden the bike normally/hard and nothing's happened but I don't want to keep pushing it and possibly clip the bike. Any ideas? "Oh help me 2 stroke community you're my only hope"
Does anyone know where I can get the right float seat replacement for my keihin fcr mx 39? (Not sure if it makes a difference but: 03 yz450f) Mine was leeking so I pulled it out thinking the Oring was bad but it didn't have one. I've looked up replacements but mine doesn't look the same. It's a press fit. Had a inner diameter of about 0.254 inch on the seat. The whole at the bottom is about 0.145 inch. The outside diameter is about 0.388 inch. The groove on the outside is 0.323 inch. It's got 2 wholes in the groove drilled 180 degrees apart from each other. (Sorry, I don't have a metric dial caliper) Ignore the threads. They are from my puller. In case your wondering how I got it out. I made a puller by drilling a whole in a 12 mm socket, tapping the float seat, and threading in a chain tensioner to get it out. Probably not the right way but thats what I had to work with. This a terrible picture of where the float seat goes. I would appreciate some pro tips before I order the wrong part. Thanks!