Search the Community
Showing results for tags 'JnsEngineering'.
Found 4 results
1 reviewAll JNS products come with a lifetime warranty against defects in materials and workmanship! These 1987-2016 KLR650 Foot Peg Lowering Brackets will drop your footpegs 1.5″ and shift them to the rear 1.0″ for a much more comfortable riding position especially for taller riders. Unlike relocation plates, these mounts do not hang dangerously below the frame! They work with aftermarket or OEM pegs and are compatible with all skid plates, crash bars, and center stands. New 10.9 high strength mounting bolts and two JNS stickers are included. Once installed the foot controls will need adjustment and the brake switch spring slightly modified.
0 commentsRecently I sold my CRF250L due to taking a new job with a 104 mile daily commute. I again almost purchased the WR250 but I decided if highway comfort, simplicity, and displacement were my prime concerns that the WR would still not fit my needs. Out of the shop I noticed that it was idling too low and stalling quite a bit. The bike easily reached 80mph for my ride home even though at this speed the vibrations were killer. I rode on it untouched for about 2 weeks and practically paid for expedited shipping from seat concepts. My other first impression of the bike was wondering where they had time to go to home depot and replace the seat with a 4x4 post. The other complaints were the rubber mounted stock pegs that made you feel like you would slip off standing up and the cramped peg location in relation to the seat and the bars. I mean it is cramped for me at 5' 8" 29 inch inseam. Where my last bike became far more fun in the woods the DR felt... a bit much to handle. The stock tires earned their reputation of the name of deathwings being far less capable than the GP22's that came stock on the 250L, yes I missed the GP22's. The rear suspension was thankfully significantly better and only required some dampening adjustment. The front suspension comparatively to the 250L was far far far worse. If you were to mix the rear stock suspension of the 250L with the front of the 650 you would have created the most poorly suspended bike conceived by man. After going from my Racetech setup on the 250L back to whatever Suzuki calls suspension I felt a bit cheated. Now here came the real test was a 329 mile back roads ride from Austin to DFW and back. (my preferred motorcycle proving ground) The average speed limit was still 75 posted and same as last time I was glad I invested in my seat concepts low seat. The bike easily plodded along at 70 - 90 mph with little complaint or trouble minus a bit of excess arm pump and vibration in my right hand. In strong cross winds the DR650 was a bit better planted but the front end due I guess to its horrifically poorly designed nature introduced more wobble than the 250L and with tucking down in wind made the ride a bit harrowing. This go around I was shy on cash and spent my first $270 on bars, grips, seat, and peg lowering kit from JNS engineering. (I also sprung for a 16T front sprocket to mitigate vibration at high speed) I could not repeat could not have made any trip over 50 miles on the stock garbage seat without reconstructive surgery on my rear. The massive upside to this bike is the ease of work on it. A valve job for instance is 4 tools and about 3 hours of work and the best part is no shims just an old fashioned tappet adjuster. The other real test was arriving at my old stomping grounds in Decatur TX at rocky ridge. This is where the 650 showed me all of it's additional weight feeling nearly unwieldy with the exception of its lower reach to the ground. My lap times which were 28 minutes modded 32 ish minutes stock on the 250L climbed up to 36 minutes on the 650 with the mixture of nearly unusable front suspension and god awful tires. At the minimum before another dirt trip this bike will have new tires and front springs. Stock for stock on the Street/ Highway the DR650 substantially outperforms the 250L but in the dirt the 250L is a good bit better for the job. As far as modding goes however I think I can achieve near if not better performance from the 650 with less money. Right off the bat for instance front and rear suspension will run about 600 to 700 less than a Racetech setup for the 250L so time will tell if this review flips. I had about $2400 into the 250L and as of this week about $307 into the 650, even if I go all out with suspension, pipe, and pumper carb I would only be out $1300. Food for thought.
1 reviewAll JNS products come with a lifetime warranty against defects in materials and workmanship! Protect the heart of your machine with a skid plate built for serious adventure. We promise you won’t regret it. No other plate offers the same protection, fit, and quality. Even your BMW buddies will be jealous! Use the drop down menu above to select your crash bar type. – 3/16″ (5mm) marine grade aluminum – Laser cut – CNC formed – Fully welded seams – Black textured powder coating – Bolts up in minutes using the provided stainless steel hardware – Superior design, materials, construction, and protection – Made in the USA!