Search the Community
Showing results for tags 'blue'.
Found 4 results
So here is the problem I am in; I want to freshen up my old 2001 WR250f, I currently have the Hurricane Hannah Graphics (Tells you when I last did this) in fact I got it by busting my butt for my dad when we were selling his house and he got the kit for me as a reward and we put it on (Great Memories); but back to being on topic. So I am searching online and I noticed that the pickings for a WR especially a 01 is about as good as a finding a women at a all male school right now. So I was wondering since the frame is unchanged until 2007 when they went to the Aluminum frame does anyone know if the 2001-2006 plastic will bolt on? Cause I want to find the Yellow Plastic again, as I am a huge fan of the old Yamaha graphics kit as you can see from my YZ250x and my 01 WR. Does anyone know who still makes yellow plastic for this old bike and if the 2001-2006 plastic (with minor mods as my 2001 YZ250f plastic that's on it needed a bit of modding) will fit on the bike? Thank you in Advance!
OK here goes... Picked up an 04 200 EXC few months back, needed some work to say the least, wont go into detail of all the things i've fixed on the bike just the current and most present issue I cant seem to fix... it is smoking IE blue smoke/lots of splooge to the point that at the end of a few hour's ride, it's out the tail pipe, running down the back and dripping onto the swing arm/rear break caliper and blue smoking quite a bit. When I first got it, it smoked more and smelled like shit. So first things first went to the carb, I live on the Oregon coast (elevation/temp reference) it's old dirty/stained but inside looks good, came with jetting pilot-45, main-178 needle: no idea what brand guessing stock in the 3rd clip, adjusted the float height due to it leaking gas when bike was upright no tilt with the gas on, Bought JD jet kit and running pilot-45, Main-185 and Needle is blue 3rd clip (JD's recommend specs for my bike @ my attitude). I have also replaced my Inner crankcase seal twice (First time I thought I messed up the O-ring so redid to make sure). I've rebuilt the top end/new piston (same thing) cleaned the PV, NOTE HERE that the PV has some issues, it seems to work fine but the screw that goes on top of the cylinder, down into the PV/flap would not come out preventing me from removing the flap to clean it, however it move's/ function's correctly, and has minimum clearance on both sides. One of the PV cover bolts that also works at the exhaust spring holder, was over torqued at some point (impact driver prob), or a result in a hard impact, the hole the bolt goes into is flailed/jared open a bit, not bad, not in the way of any function/ PV Gearing/hinge, it is not needed for that area to be air tight as their is also a breather that goes out of the PV so will not result in an "air leak" or loss in Top end PSI.... anyway... it's still smoking.... quite a bit.. now the bike itself rides fine I feel, the carb does puke gas when tilted over slightly/ hard to start (kick start) after flooded (like all bikes tho) I don't have any stalling/low idle issues outside of user error on clutch control. Honestly outside of it smoking as much as it does I would think nothing is wrong with it.. I have also tried raising the needle Clip to 2nd clip and it changed nothing at all, not even feel of the bike/response and have a new Spark plug I have yet to put on the bike. I have also "compromised" the crankcase Gasket (new one in the mail) while I was putting the Crankcase back on but that should do nothing with the exhaust just a little gear oil leak not relevant but throwing it out there. So I am at a loss... I've been toying with the idea of getting a Lectron carb... However... would hate to drop $400~$500 and the issue still persist, if it's a jetting/carb/float issue that would fix it and improve MPH/fuel consumption Or something with the PV? but I don't see the PV causing that much smoke/sploogee... I've ridden the bike normally/hard and nothing's happened but I don't want to keep pushing it and possibly clip the bike. Any ideas? "Oh help me 2 stroke community you're my only hope"
So like an idiot I was on craigslist and found a very cheap Enduro 250. The problem is I have no idea what year or brand of bike it is due to the VIN number being scratched off on the bike. Wondering if anyone recognizes this bike or can identify what kind of a bike it is. I can attach images of the bike below. THANKS!