Search the Community
Showing results for tags 'topendblown'.
OK here goes... Picked up an 04 200 EXC few months back, needed some work to say the least, wont go into detail of all the things i've fixed on the bike just the current and most present issue I cant seem to fix... it is smoking IE blue smoke/lots of splooge to the point that at the end of a few hour's ride, it's out the tail pipe, running down the back and dripping onto the swing arm/rear break caliper and blue smoking quite a bit. When I first got it, it smoked more and smelled like shit. So first things first went to the carb, I live on the Oregon coast (elevation/temp reference) it's old dirty/stained but inside looks good, came with jetting pilot-45, main-178 needle: no idea what brand guessing stock in the 3rd clip, adjusted the float height due to it leaking gas when bike was upright no tilt with the gas on, Bought JD jet kit and running pilot-45, Main-185 and Needle is blue 3rd clip (JD's recommend specs for my bike @ my attitude). I have also replaced my Inner crankcase seal twice (First time I thought I messed up the O-ring so redid to make sure). I've rebuilt the top end/new piston (same thing) cleaned the PV, NOTE HERE that the PV has some issues, it seems to work fine but the screw that goes on top of the cylinder, down into the PV/flap would not come out preventing me from removing the flap to clean it, however it move's/ function's correctly, and has minimum clearance on both sides. One of the PV cover bolts that also works at the exhaust spring holder, was over torqued at some point (impact driver prob), or a result in a hard impact, the hole the bolt goes into is flailed/jared open a bit, not bad, not in the way of any function/ PV Gearing/hinge, it is not needed for that area to be air tight as their is also a breather that goes out of the PV so will not result in an "air leak" or loss in Top end PSI.... anyway... it's still smoking.... quite a bit.. now the bike itself rides fine I feel, the carb does puke gas when tilted over slightly/ hard to start (kick start) after flooded (like all bikes tho) I don't have any stalling/low idle issues outside of user error on clutch control. Honestly outside of it smoking as much as it does I would think nothing is wrong with it.. I have also tried raising the needle Clip to 2nd clip and it changed nothing at all, not even feel of the bike/response and have a new Spark plug I have yet to put on the bike. I have also "compromised" the crankcase Gasket (new one in the mail) while I was putting the Crankcase back on but that should do nothing with the exhaust just a little gear oil leak not relevant but throwing it out there. So I am at a loss... I've been toying with the idea of getting a Lectron carb... However... would hate to drop $400~$500 and the issue still persist, if it's a jetting/carb/float issue that would fix it and improve MPH/fuel consumption Or something with the PV? but I don't see the PV causing that much smoke/sploogee... I've ridden the bike normally/hard and nothing's happened but I don't want to keep pushing it and possibly clip the bike. Any ideas? "Oh help me 2 stroke community you're my only hope"
So I recently got a 2002 kx125. Rode it for a day and it ran beautiful. Let my brother ride it and he was ok first tried to shift to second but hit neutral revved it to the sky than dropped it back in first... it bogged, died and it was a long push back to the truck. Now I tore the bike down took off the cylinder (doesn't look bad will post a pic) but the top of the piston was shreded like a piece of metal got in and it was slamming against to top of the cylinder head.(will post pic) now I was told there was no doubt the metal came from a bearing in the bottom end and the bottom end was blown. But the kick start is moving smooth and there's no play in the crank and it's on great shape. I took off the left and right crank cases and it looks brand new like it was already rebuilt recently and there is zero play in fly wheel. (Will post pic) so I started digging around the cylinder and come to find out there is a chip on the left side of the power valve kip(will post pic) any way that's the metal that got in there? I inspected carb and reeds(they had a small hole but nothing crazy) I drained all fluids and there was a small metal shard or two in the oil nothing crazy. Please help I don't want to have to split the cases if I don't have to.